manualshive.com logo in svg

LocoCruiser LC201, Руководство пользователя

Поделиться
Скачать
LocoCruiser LC201 Скачать руководство пользователя страница 10

 

LocoCruiser standard series decoder user manual Ver1.0 

 

9 

The wire color comparison table of 6-pin DCC-standard interface   

No. 

Color 

Connect 

1 

Orange 

Motor + 

2 

Gray 

Motor - 

3 

Red 

Right track 

4 

Black 

Left track 

5 

White 

Front light - 

6 

Yellow 

Rear light - 

Please make sure all connected wires are correct.   Connecting wrong wire could  destroy the 

decoder. 

 

4.5.1 Wiring Diagram for LocoCruiser LC202 

 

 
4.6 Locomotive with 21-pin DCC-standard Interface 

According to the instructions in the locomotive manual, remove the body shell, and find the 21 

pin plug. First, remove the plug from the socket and find the correct direction( Usually there’s a 

number or arrow marked “pin 1” on the 8 pin head. And then fit with 8 pin head, you’ll finish the 

installation.   

 

4.6.1 Wiring Diagram for LocoCruiser LC203 

 

4.7 Connecting Additional Functions 

  The Series 2 decoders have 4~6 additional functions.    Each function output can reach 

300mA. 

Содержание LC201



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды