background image

Copyright © 2021, ASSA ABLOY Australia Pty Limited. All rights reserved. Reproduction in whole or

in part without the express written permission of ASSA ABLOY Australia Pty Limited is prohibited.

700002AU  Rev 2  06/21

14

5831 Series

 Installation and Operating Instructions

1 .  Make sure 3 Position switch on battery pack 

is in OFF position . 

2 .  Attach battery pack wiring connector to 

operator receptacle .  

 

Note:

 Connector is keyed to prevent 

attaching incorrectly . 

3 .  Using T channel, slide battery pack onto 

operator making sure wires are tucked into 

operator cavity and not pinched . 

4 .  Toggle 3 Position switch to ON position .

3 Position

Switch

Battery

Connector

Auxiliary

Connector

LED

Figure 27 

Install Battery Pack

Press and hold 3 Position switch in “OPTION” 

position . 

 

•  Green LED = fully charged . 

•  Yellow LED = partially drained . 

•  Red LED = fully drained (operator will 

not function in automatic mode) 

NOTE:

 Battery can be charged by using a 

battery charger, a Plug-In 24VDC power supply, 

or by allowing manual traffic to restore battery 

power .

Figure 28 

3 Position Switch

LED

T Channel

Adjust Door Spring Tension If Necessary

1 .  Manually open and close door several times to make 

sure door opens and closes smoothly . 

2 .  If door feels too light, use 3/16" hex wrench to turn 

screw clockwise to increase spring tension . 

If door feels too heavy, use 3/16" hex wrench to turn 

screw counter clockwise to decrease spring tension . 

NOTE:

 Operator is shipped with spring tension set to 

one half of maximum spring tension . 

Increase 

Spring Force

Clockwise

Decrease 

Spring Force

Counter Clockwise

Figure 29 

Check Battery Voltage

Содержание ASSA ABLOY 5831 Series

























Отзывы: