Lochinvar 140H Скачать руководство пользователя страница 5

Страница: 5 / 76

Page

INTRODUCTION

• This manual provides information necessary for the installation, operation, and maintenance of the

water heater.

• The model description is listed on the rating plate which is attached to the side/front panel of the

water heater.

• Please read all installation instructions completely before installing this product.

• If you have any problems or questions regarding this equipment, consult the manufacturer or its

local representative.

• This equipment is an on-demand, tankless water heater designed to efficiently supply endless hot

water for your needs when properly sized and installed.

• These

high efficiency models

have a built-in secondary heat exchanger that absorbs latent heat

from the exhaust gas.

• The Indoor models are only to be installed indoors. The Outdoor models are only to be installed

outdoors.

• The principle behind tankless water heaters is simple:

Exhaust

Secondary

heat exchanger

Intake port

Condensate

drain port

Cold water inlet

Gas

Hot water outlet

Computer board

Fan motor

Gas valves

Igniter

Thermistor

Bypass valve

Primary

heat exchanger

Exhaust thermistor

Water control valve

Thermistor

Flow sensor

Burners

*This diagram illustrates tankless water heater design concepts only and does not accurately represent the

water heater’s physical description.

1. A hot water fixture is turned on.

2. Water flows through the heater.

3. The water flow sensor detects the water flow.

4. The computer initiates the fan motor and gas valve to let gas flow through the heater and sends a signal to

the igniter to create an ignition spark.

5. The gas ignites and flames appear within the burner chamber.

6. Water is heated as it flows through the heat exchanger.

7. Using thermistors to measure temperatures throughout the water heater, the computer modulates the gas

and water valves to ensure proper output water temperature and hot water outflows.

8. When the fixture is turned off, the unit shuts down.

Introduction

Installation Manual

Содержание 140H













































































Результаты поиска

Содержание 140H

Отзывы:

Похожие инструкции для 140H

Бренды по названию

Популярные бренды

Lochinvar 140H, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание 140H

Отзывы:

Похожие инструкции для 140H

Бренды по названию

Популярные бренды