Lochinvar 140H Скачать руководство пользователя страница 11

Страница: 11 / 76

Page

Installation

Installation Manual

WARNING FOR INSTALLATIONS

FOR YOUR SAFETY, READ BEFORE INSTALLATION:

Do not install the heater where water, debris or

flammable vapors may get into the flue terminal.

This may cause damage to the heater and void

the warranty.

Do not have the vent terminal pointing toward

any opening into a building. Do not locate

your heater in a pit or location where gas and

water can accumulate.

Do not install next to a dryer or any source

of airborne debris that can be trapped inside

the combustion chamber, unless the system

is direct-vented.

Prohibited

Ensure that you meet the minimum clearances

shown below for a direct vent termination:

Ensure that you meet the minimum clearances

shown below for Outdoor vent termination:

Locate the outdoor water heater so it's vent terminal

meets the following clearances. Locate the vent terminal

of an indoor heater to meet the following clearances:

2 ft (61 cm) from an inside corner

2 ft (61 cm) from an outside corner

3 ft (91 cm) below a soffit/overhang

4 � min.

USA: 1 � (30 cm) min.

Canada: 3 � (91 cm) min.

USA: 1 � (30 cm) min.

Canada: 3 � (91 cm) min.

USA: 1 � (30 cm) min.

Canada: 3 � (91 cm) min.

USA: 1 � (30 cm) above grade and

above an�cipated snow level

Canada: 1 � (30 cm) above grade

An�cipated snow level

Outside

corner

Inside

corner

2 ft

(61 cm)

3 ft

(91 cm)

2 ft

(61 cm)

Содержание 140H













































































Результаты поиска

Содержание 140H

Отзывы:

Похожие инструкции для 140H

Бренды по названию

Популярные бренды

Lochinvar 140H, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание 140H

Отзывы:

Похожие инструкции для 140H

Бренды по названию

Популярные бренды