Lochinvar 140H Скачать руководство пользователя страница 22

Страница: 22 / 76

Page

Installation

Installation Manual

-DIP switch settings for vent length-

Typical installations using

PVC, CPVC, ABS, or polypropylene vent

WARNING

• Adjust the appropriate DIP switches according to model and vent length as shown

below. DO NOT adjust the other DIP switches.

• Turn off the power supply to the water heater before changing the DIP switch settings.

• Failure to observe these warnings could lead to carbon monoxide poisoning or death.

• For details of the vent items, refer to the Installation manual

for each item.

• For clearance information, refer to pages 14 to 16.

Termination

Hanger

Vent connections for

Single-pipe with Room-Air Intake Installation, Horizontal Installation

*3" street elbow

with bird screen

Intake vent collar

with 3" adapter

(Female)

3"x 2" reducer

2" straight pipe

Exhaust vent

collar with 3"

adapter

(Female)

inch

vent installation for 140H model

• 2

ʺ pipe for venting is only approved for the 140H model in the Single Pipe with Room-Air Intake Installation,

Horizontal Installation as shown below.

• Maximum vent length for 2

ʺ venting is 6.5 ft (2.0 m) , not including termination.

•

One long sweep elbow may be installed. Deduct 5 ft (1.5 m) from maximum vent length.

• 2

ʺ venting is approved on installations up to 3,000 ft (914 m).

Vent length

Single vent

5 to 6.5 ft

(1.5 to 2.0 m)

OFF

ON 1 2 3 4 5 6 7 8 9 10

No. 6 : ON

No. 7 : ON

Bank of DIP switches

140H Computer board

3" PVC adapters are not approved for use in Canada.

NOTICE

1. Insert no more than 12" (305 mm) of 3" straight pipe into

the exhaust vent collar with 3" adapter.

2. Connect a 3" x 2" reducer with the 3" straight pipe.

3. Connect 2" straight pipe into the reducer.

4. Connect spigot end of the 3" street elbow into the intake

vent collar with 3" adapter. Be sure to insert a bird screen

into the hub side.

*The bird screen that fits into the 3 inch elbow is supplied

with the indoor water heater.

Содержание 140H













































































Результаты поиска

Содержание 140H

Отзывы:

Похожие инструкции для 140H

Бренды по названию

Популярные бренды

Lochinvar 140H, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание 140H

Отзывы:

Похожие инструкции для 140H

Бренды по названию

Популярные бренды