background image

IOMVIFB-8

4830 TRANSPORT DRIVE, DALLAS TX 75247

TEL.: (214) 638-6010

www.ljwing.com 

WARNING: Improper installation, adjustment, alteration, service or maintenance 

can cause property damage, injury or death. Read the installation, operating and 

maintenance instructions thoroughly before installing or servicing this equipment.  

INSTALLER'S RESPONSIBILITY

Installer Please Note: This equipment has been test fired and inspected.  It has been shipped 

free from defects from our factory.  However, during shipment and installation, problems such as 

loose wires, leaks or loose fasteners may occur.  It is the installer’s responsibility to inspect 

and correct any problems that may be found.

ATTENTION: READ CAREFULLY BEFORE ATTEMPTING TO INSTALL, OPERATE OR SERVICE THIS 

EQUIPMENT. RETAIN FOR FUTURE REFERENCE.

POST AND MAINTAIN THESE INSTRUCTIONS IN LEGIBLE CONDITION.

INSTALLATION, OPERATION AND

MAINTENANCE MANUAL

VERTICAL TUBE HEATING COILS 

MV & VIFB MODELS

SAVE THIS MANUAL

ATTENTION: READ THIS MANUAL AND ALL LABELS ATTACHED TO THE UNIT CAREFULLY BEFORE 
ATTEMPTING TO INSTALL, OPERATE OR SERVICE THESE UNITS! CHECK UNIT DATA PLATE FOR 
STEAM OR HOT WATER REQUIREMENTS AND ELECTRICAL SPECIFICATIONS AND MAKE CERTAIN 
THAT THESE AGREE WITH THOSE AT POINT OF INSTALLATION. RECORD THE UNIT MODEL AND SE-
RIAL No.(s) IN THE SPACE PROVIDED.  RETAIN FOR FUTURE REFERENCE. THE APPLIANCE IS NOT 
TO BE USED BY PERSONS (INCLUDING CHILDREN) WITH REDUCED PHYSICAL, SENSORY OR MEN-
TAL CAPABILITIES, OR LACK OF EXPERIENCE AND KNOWLEDGE, UNLESS THEY HAVE BEEN GIVEN 
SUPERVISION OR INSTRUCTION. CHILDREN SHOULD BE SUPERVISED TO ENSURE THAT THEY DO 
NOT PLAY WITH THE APPLIANCE.

WING Model No.   

 

 

 

 

Serial No.

Wing MV & VIFB coil performance 

is certified by the Air-Conditioning, 

Heating, and Refrigeration Institute 

(AHRI) under AHRI Standard 410 

for maximum working pressures 

up to 200 PSIG and temperatures 

up to 400° F.

Wing MV & VIFB coils are listed 

by Engineering Test Laboratories 

(ETL) to Underwriter Laboratories 

(UL) Standard 1995. This 

standard assures that Wing coils 

are safe to operate up to a design 

pressure of 100 PSIG. 

Содержание MV

























Отзывы: