Lissmac MULTICUT 550 GH Скачать руководство пользователя страница 50

Страница: 50 / 92

50/92

7.13.

Floor saw shut-down

WARNING

Crush hazard from unintended movement

Personal and material damage from accidentally rolling machine.



Always activate the parking lock before leaving the machine

Shutdown



Raise saw blade with switch (Pos. 7) to have ample ground clearance



Deactivate the water pump with switch (Pos. 2) and close ball valve of water supply



Set engine throttle forward to idle (Pos. 4)



Activate parking lock (Pos. 9) at standstill



Wait for saw blade to spin out to a standstill



Switch off ignition (Pos. 1) and remove key.

NOTICE

Storing the 3-speed gearbox

During prolonged storage or periods of nonuse, internal components will lose their lubrication film.

Start the machine or manually turn the gears at least once every 6 months to reestablish the protective
lubricating film.

Содержание MULTICUT 550 GH





























































































Результаты поиска

Содержание MULTICUT 550 GH

Отзывы:

Похожие инструкции для MULTICUT 550 GH

Бренды по названию

Популярные бренды

Lissmac MULTICUT 550 GH, Руководство по эксплуатации

Результаты поиска

Содержание MULTICUT 550 GH

Отзывы:

Похожие инструкции для MULTICUT 550 GH

Бренды по названию

Популярные бренды