Lissmac MULTICUT 550 GH Скачать руководство пользователя страница 58

Страница: 58 / 92

58/92

7.23.

Cutting with open blade guard

WARNING

Ejected parts and cut hazard from open blade guard

Serious personal injury from contact with running blade or ejected parts.



Cordon off cut area



Never touch the rotating blade



Wear hard hat, goggles and safety boots



Stop engine and wait for all parts to stand still before working on the blade guard.

Sequence

The front part of the blade guard can be folded up. This function is used to make
corner cut at walls.

•

Stop engine and wait for all parts to stand still

•

Loosen bolts on side of blade guard (Pos. 1)

•

Fold up front part

•

Secure position by tightening bolt (Pos. 2)

After the cut

•

Stop engine and wait for all parts to stand still

•

Close blade guard immediately and secure with bolts (Pos. 1)

Содержание MULTICUT 550 GH





























































































Результаты поиска

Содержание MULTICUT 550 GH

Отзывы:

Похожие инструкции для MULTICUT 550 GH

Бренды по названию

Популярные бренды

Lissmac MULTICUT 550 GH, Руководство по эксплуатации

Результаты поиска

Содержание MULTICUT 550 GH

Отзывы:

Похожие инструкции для MULTICUT 550 GH

Бренды по названию

Популярные бренды