Lissmac MULTICUT 550 GH Скачать руководство пользователя страница 29

Страница: 29 / 92

29/92

4.6.

Checking v-belt tension

WARNING

Cut and crush hazard from rotating v-belt drive

When touching the rotating v-belt, hands and clothing can become entangled and pulled in, resulting in cut
and crush injuries including dismemberment.



Do not open or remove the belt guard or touch the v-belt while it rotates.



Only perform this work with the engine turned off and pulleys standing still.

Check

V-belt tension can be checked by pushing them with a finger.

•

Remover the belt cover

•

Check by pushing with a finger, the drive belts must yield about one belt
strength

Effects of incorrectly

tightened drive belts:



Drive belts too loose:
The drive belts slip on the V-belt sheave.
Excessive wear and no or poor power transmission.



The drive belt is tightened too much:
Excessive wear and heating of the V-belt and sheave with subsequent damages

Содержание MULTICUT 550 GH





























































































Результаты поиска

Содержание MULTICUT 550 GH

Отзывы:

Похожие инструкции для MULTICUT 550 GH

Бренды по названию

Популярные бренды

Lissmac MULTICUT 550 GH, Руководство по эксплуатации

Результаты поиска

Содержание MULTICUT 550 GH

Отзывы:

Похожие инструкции для MULTICUT 550 GH

Бренды по названию

Популярные бренды