Lippert Components Ground Control 2.0 Скачать руководство пользователя страница 156

Страница: 156 / 166

Rev: 11.08.19

Page 156

CCD-0001573-08

System Information

The X-Trek is a stabilizing system for trailers utilizing hydraulic stabilizers and a manual bi-direction pump to

simultaneously extend or retract all of the stabilizers.

Safety

This manual provides general instructions. Many variables can change the circumstances of the intended

instructions, i.e. the degree of difficulty involved in the service operation and the ability of the individual

performing the operation. This manual cannot begin to plot out instructions for every possibility, but will

provide the general instructions, as necessary, for effectively installing, operating and servicing the device,

product or system. In the event the skill level required is too advanced or the procedure too difficult, a

certified technician should be consulted before performing the necessary service. Failure to correctly

perform a troubleshooting procedure may result in voiding the warranty, inflicting personal injury or death.

The "WARNING" symbol above is a sign that a procedure has a safety risk involved and may cause death

or serious personal injury if not performed safely and within the parameters set forth in this manual.

Failure to follow instructions provided in this manual may result in death, serious personal injury

and/or severe product and property damage, including voiding of the component warranty.

Trailer MUST be supported per manufacturer's recommendations before working underneath.

Failure to do so may result in death or serious personal injury.

Failure to act in accordance with the following may result in death or serious personal injury. The

use of X-Trek to support the trailer for any reason other than which it is intended is prohibited by

Lippert’s limited warranty. The Lippert stabilizing system is designed as a “stabilizing” system only

and should not be used to provide service for any reason under the trailer such as changing tires or

servicing the stabilizing system. Any attempts to change tires or perform other service while trailer

is supported by X-Trek could result in damage to the trailer and/or cause death or serious injury.

LEVELING AND STABILIZATION

X-TREK STABILIZATION SYSTEM

Содержание Ground Control 2.0







































































































































































Результаты поиска

Содержание Ground Control 2.0

Отзывы:

Похожие инструкции для Ground Control 2.0

Бренды по названию

Популярные бренды

Lippert Components Ground Control 2.0, Руководство владельца

Результаты поиска

Содержание Ground Control 2.0

Отзывы:

Похожие инструкции для Ground Control 2.0

Бренды по названию

Популярные бренды