Linn CLASSIK AFEKT Скачать руководство пользователя страница 3

UK USERS PLEASE READ THIS IMPORTANT
SAFETY INFORMATION

Replacing the fuse in the mains plug

This appliance is fitted with a non-rewireable 13 Amp mains plug. The plug contains a 5 Amp
fuse. If the fuse has blown it can be replaced as follows:

a)  Pull out the red fuse cover/carrier.
b)  Remove and dispose of the blown fuse.
c)  Fit a new 5 Amp BS1362 approved fuse into the carrier and push the carrier

back into the plug.

Always ensure the fuse cover is fitted. If the fuse cover is missing do not use the plug. Contact
your Linn retailer to obtain a replacement fuse cover. Fuses are for fire protection and do not
protect against electric shock.

Mains plug replacement

Should your mains plug need replacing and you are competent to do this proceed as follows.
If you are in doubt contact your Linn retailer or a competent electrician.

a)  Disconnect the plug from the mains supply.
b)  Cut off the plug and dispose of it safely. A plug with bared conductors is

dangerous if engaged in a live socket.

c)  Only fit a 13 Amp BS1363A approved plug with a 5 Amp fuse.

most quality plugs. Attach the wires securely to their respective points.
The Brown wire must go to the Live pin, the Blue wire must go to the Neutral 
pin, and the Green/Yellow wire must go to the Earth pin.

d)  Before replacing the plug top ensure that the cable restraint is holding th e

outer sheath of the cable firmly and that the wires are correctly connected.

WARNING

THIS APPLIANCE MUST BE EARTHED.

English

Replacing the fuse in the
CLASSIK AFEKT speaker

Should the mains fuse blow, replace it only with an equivalent part (see table
below). The fuse holder is located just below the mains inlet socket. To replace the
fuse, disconnect the product from the mains supply, remove the fuse using a flat
blade screwdriver, insert a new fuse. If the fuse blows a second time there is a fault
in the product; contact your local retailer.

Fuse selection table

MAINS  INPUT VOLTAGE

FUSE TYPE

100V

125V T6.3AL

115V

125V T6.3AL

230V

250V T3.15AL

CLASSIK AFEKT

BASS REINFORCEMENT SPEAKER

OWNER’S MANUAL

Содержание CLASSIK AFEKT











Отзывы: