Linksys LRT214 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 77

background image

30

System Management

Linksys

System Management

You can configure advanced setting in System Management category, please
refer to following items:
•

Dual WAN (LRT224 Only) / Network Service Detection

•

Bandwidth Management

•

Session Control

•

SNMP

•

SSL Certificate

Dual WAN (LRT224 Only) / Network
Service Detection

Dual WAN

You can choose Link Failover or Load Balance mode when you use the Dual
WAN setting . Go to

Configuration > System Management > Dual WAN

.

NOTE:

Remember to click Save before leaving the page . You can also click
Cancel to undo the changes .

Mode

You can configure two Internet connections by using the WAN and the WAN/DMZ port .
Two modes can be selected:

Link Failover:

Only the primary WAN port works in normal time; the
other WAN is a backup port .

If the primary WAN connection is unavailable, the backup
WAN connection will take over the traffic .

Load Balance:

Two WAN ports will work simultaneously . The router will
balance traffic between the two ports .

Network Service Detection

This is a detection system for network external services . If this option is selected,
information such Retry or Retry Timeout will be displayed . If two WANs are
used for external connection, be sure to activate the NSD system, so as to avoid
any unwanted break caused by the device misjudgment of the overload traffic
for the WAN .

«
...
32
33
34
35
36
...
»

Содержание LRT214














































































Отзывы:

Нет отзывов

Похожие инструкции для LRT214

Бренд: National Instruments Страницы: 16

Бренд: National Instruments Страницы: 23

Бренд: Datasheen Страницы: 25

Fan Tray 8820-S2-900

Бренд: Paradyne Страницы: 6

Бренд: AIC Страницы: 101

ADSL Ethernet & USB Combo Router Lynx L-510

Бренд: Starbridge Networks Страницы: 59

Бренд: Matrix Switch Corporation Страницы: 60

IntraSwitch 5324MT

Бренд: Asante Страницы: 2

ClareVision CV-M161620-04

Бренд: Clare Controls Страницы: 32

Бренд: Me Страницы: 28

Бренд: Lanner Страницы: 80

Бренд: Lanner Страницы: 116

Бренд: Nedap Страницы: 3

EIR508-2-T Series

Бренд: B&B Electronics Страницы: 71

PCNA EP OCe14102

Бренд: Fujitsu Страницы: 20

Бренд: Fujitsu Страницы: 34

BS2000 SE Series

Бренд: Fujitsu Страницы: 43

BS2000 SE Series

Бренд: Fujitsu Страницы: 93

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды