Linksys LRT214 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 77

background image

27

DHCP

Linksys

RA Flags:

When Managed is checked, IP information can be
found on the DHCPv6 server in LAN.

When Other is checked, IP and other information,
such as DNS server, can be got from DHCPv6
server in LAN.

You can check or uncheck both options.

Router Preference:

If two routers are accessible, the one with the
higher preference will be chosen by the host.
Choose High, Medium or Low.

MTU: (Maximum
Transmission Unit)

Input MTU value. MTU is the largest packet size
can be sent.

Router Lifetime

Router advertisements expire after a period
determined by you. Devices on the network will
not try to access a router at an expired address.

IP & MAC Binding (for IPv4 Only)

IP & MAC Binding assigns IP addresses to specific devices. In this way, you can
also make sure that users can not add extra PCs for Internet access or change
private IP addresses.

NOTE:

Remember to click Save before leaving the page. You can also click
Cancel to leave without any change.

IP & MAC Binding

•

Set up IP & MAC Binding from IP & MAC Table

Click Show unknown MAC addresses button, an IP address and MAC table
will appear. Input a name for the device and check Enable box to bind the IP
and MAC addresses.

Click OK to save the configuration or Close to leave without saving. You can
also click Refresh to update the table.
- Set up IP & MAC Binding Manually

«
...
29
30
31
32
33
...
»

Содержание LRT214














































































Отзывы:

Нет отзывов

Похожие инструкции для LRT214

Бренд: Watchguard Страницы: 40

Бренд: D-Linke Страницы: 32

TokenLink Velocity 3C319

Бренд: 3Com Страницы: 2

Бренд: B+B SmartWorx Страницы: 4

Бренд: QNAP Страницы: 54

Бренд: Infoblox Страницы: 13

Бренд: QUNDIS Страницы: 42

Бренд: Abocom Страницы: 63

Бренд: Zoom Страницы: 31

McDATA Eclipse 1620

Бренд: Sun Microsystems Страницы: 9

Бренд: NETGEAR Страницы: 152

Бренд: Mobily Страницы: 12

Бренд: NetComm Страницы: 4

Бренд: Baileigh Страницы: 20

Бренд: Orcon Страницы: 2

VDA-NVR2108W4KS2

Бренд: Dahua Technology Страницы: 363

Бренд: Orcomm Страницы: 10

Бренд: X-Micro Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды