LineEye LE-2500XR Скачать руководство пользователя страница 117

Страница: 117 / 140

-115-

When monitoring in synchronization with an external clock.

9.3 About the Frame

The definition of 1 frame is as shown in the table below for each protocol.

When performing a simulation with DCE (this unit is in DTE mode).

When performing a simulation with DTE (this unit is in DCE mode).

ST1

CLOCK:ST1

DCE

Analyzer

DTE

ST2

CLOCK:ST2

DCE

Analyzer

DTE

CLOCK:RT

DCE

Analyzer

DTE

ST1

CLOCK:ST1

DTE

Analyzer

DCE

ST2

CLOCK:ST2

DTE

Analyzer

DCE

CLOCK:RT

DTE

Analyzer

DCE

ST1

Analyzer

CLOCK:ST1

DTE

DCE

ST2

Analyzer

CLOCK:ST2

DTE

DCE

Analyzer

CLOCK:RT

DTE

DCE

Protocol

Definition of 1 frame

ASYNC

Data string until the idle time longer than one set at “Frame end time” in the configuration

is detected or the data set at “Frame end code” is received.

SYNC

・

BSC

Data string from the synchronization establishment character set at “Sync code” in the

configuration to the synchronization release character set at “Reset code”.

HDLC

・

SDLC

Data string from start flag to end flag.

ASYNC-PPP

Data string from flag character (7Eh) to flag character (7Eh).

MODBUS

In RTU mode, the data string until detecting the non-communication time of silent inter-

val (3.5 characters) or more.

In ASCII mode, Data string from start code (3Ah) to end code (0Dh, 0Ah).

I2C

Data sequence from start sequence detection to stop sequence detection.

SPI

Data string received while the SS signal is active.

Burst

Data string until an idle time set at “Frame end time” in the configuration or more is de

tected.

Содержание LE-2500XR













































































































































Результаты поиска

Содержание LE-2500XR

Отзывы:

Похожие инструкции для LE-2500XR

Бренды по названию

Популярные бренды

LineEye LE-2500XR, Инструкция по эксплуатации

Результаты поиска

Содержание LE-2500XR

Отзывы:

Похожие инструкции для LE-2500XR

Бренды по названию

Популярные бренды