Lincoln Electric SA-400I Скачать руководство пользователя страница 31

Страница: 31 / 68

E-8

TROUBLE SHOOTING

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your

Local Lincoln Authorized

Field Service Facility

for technical troubleshooting assistance before you proceed.

SA-400I

CAUTION

Observe all Safety Guidelines detailed throughout this manual

PROBLEMS

(SYMPTOMS)

POSSIBLE

CAUSE

RECOMMENDED

COURSE OF ACTION

White or Blue Smoke.

Dark Grey Smoke.

Faulty Charging.

Starter Motor does not run.

Engine Protection Light not coming on.

No Auxiliary Power

   1.     Excess engine oil.
2.     Too low viscosity of the engine oil.
3.     Faulty injection timing.

1.     Unsuitable fuel.
2.     Excess injection.
3.     Faulty function of the engine.
4.     Overloading.
5.     Clogged air cleaner.

1.     Loose fan belt.
2.     Faulty wiring.
3.     Faulty battery.
4.     Worn out alternator brush.

1.     Loose or damaged wiring.
2.     Drained voltage from battery.
3.     Damaged  starter  motor  (including

solenoid).

1. Faulty light wiring.
2. Faulty Engine Control Unit.

3. Faulty LED indicator.

1. GFCI may have tripped. Follow

“GFCI Testing and Resetting
Procedure” in the MAINTENANCE
section of this manual.

2.    Open breakers may need to be reset.
3.    Faulty receptacle.
4.    Faulty auxiliary circuit wiring.

If all recommended possible areas of mis-
adjustment have been checked and the
problem persists,

Contact your local

Lincoln Authorized Field Service
Facility.

Содержание SA-400I





































































Результаты поиска

Содержание SA-400I

Отзывы:

Бренды по названию

Популярные бренды

Lincoln Electric SA-400I, Руководство оператора

Результаты поиска

Содержание SA-400I

Отзывы:

Бренды по названию

Популярные бренды