Lincoln Electric SA-400I Скачать руководство пользователя страница 29

Страница: 29 / 68

E-6

TROUBLE SHOOTING

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your

Local Lincoln Authorized

Field Service Facility

for technical troubleshooting assistance before you proceed.

SA-400I

CAUTION

Observe all Safety Guidelines detailed throughout this manual

PROBLEMS

(SYMPTOMS)

POSSIBLE

CAUSE

RECOMMENDED

COURSE OF ACTION

Engine does not start.

Engine does not turn over.

Irregular running of the engine.

Engine stops during operation and the

Engine Protection light

does not

turn on.

1. Lack of fuel.

2. Air mixed in the fuel system.

3. Clogged fuel filter.

4. Irregular and faulty fuel supply

(Injector pump trouble).

5. Glow plug not heated.

6. Clogged air cleaner.

7. No compression.

8. Engine protection light is ON.

1. Faulty Ignition switch and or

Injector pump solenoid.

2. Insufficient charging or complete

discharge of the battery.

3. Improper viscosity of the lubricat-

ing oil.

1. Air mixed in the fuel system.

2. Uneven fuel injection (Faulty fuel

injector pump).

3. Clogged fuel filter.

4. Defective governor.

5. Engine itself defective.

1. Lack of fuel in the fuel tank.

2. Clogged fuel filter.

3. Air mixed in the fuel system.

4. Faulty function of the engine.

If all recommended possible areas of mis-
adjustment have been checked and the
problem persists,

Contact your local

Lincoln Authorized Field Service
Facility.

Содержание SA-400I





































































Результаты поиска

Содержание SA-400I

Отзывы:

Бренды по названию

Популярные бренды

Lincoln Electric SA-400I, Руководство оператора

Результаты поиска

Содержание SA-400I

Отзывы:

Бренды по названию

Популярные бренды