manualshive.com logo in svg

Lincoln Electric SA-400I, Руководство оператора

Поделиться
Скачать
Lincoln Electric SA-400I Скачать руководство пользователя страница 24

HOW TO USE TROUBLESHOOTING GUIDE

E-1

TROUBLE SHOOTING

SA-400I

®

This Troubleshooting Guide is provided to help you locate and
repair possible machine malfunctions.  Simply follow the three-
step procedure listed below.

Step 1.

LOCATE PROBLEM (SYMPTOM).

Look under the column labeled “PROBLEM (SYMPTOMS)”.  This
column describes possible symptoms that the machine may
exhibit.  Find the listing that best describes the symptom that the
machine is exhibiting. 

Step 2.

POSSIBLE CAUSE.

The second column labeled “POSSIBLE CAUSE” lists the obvious
external possibilities that may contribute to the machine symptom.  

Step 3.

RECOMMENDED COURSE OF 
ACTION

This column provides a course of action for the Possible Cause,
generally it states to contact your local Lincoln Authorized Field
Service Facility.

If you do not understand or are unable to perform the
Recommended Course of Action safely, contact your local Lincoln
Authorized Field Service Facility.

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your

Local  Lincoln Authorized

Field Service Facility

for technical troubleshooting assistance before you proceed.

Service and Repair should only be performed by Lincoln Electric Factory
Trained Personnel.  Unauthorized repairs performed on this equipment may
result in danger to the technician and machine operator and will invalidate
your factory warranty.  For your safety and to avoid Electrical Shock, please
observe all safety notes and precautions detailed throughout this manual.

Have  qualified  personnel  do  the  troubleshooting  work.
Turn the engine off before working inside the machine. In
some cases, it may be necessary to remove safety guards
to  perform  required  maintenance.    Remove  guards  only
when necessary and replace them when the maintenance
requiring their removal is complete. Always use the great-
est care when working near moving parts.

Do not put your hands near the engine cooling blower fan.
If a problem cannot be corrected by following the instruc-
tions,  take  the  machine  to  the  nearest  Lincoln  Field
Service Shop.

------------------------------------------------------

WARNING

WARNING

CAUTION

Содержание SA-400I





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды