Lincoln Electric FLEX FEED 74 HT Скачать руководство пользователя страница 8

Страница: 8 / 59

A-1

INSTALLATION

FLEX FEED™ 74 HT

TECHNICAL SPECIFICATIONS – FLEX FEED™ 74 HT (K3883-XX)

TEMPERATURE RANGE

OPERATION:

-40°F to 104°F (-40°C to 40°C)

STORAGE:

-40°F to 122°F (-40°C to 50°C)

INPUT VOLTAGE and CURRENT

HEIGHT

WIDTH

DEPTH WEIGHT

Wire

11.1 Inches

13.6 Inches 13.3 Inches 36 lbs.

Drive ( 294mm) (345mm)

(337mm) (16.3kg)

(only)

PHYSICAL DIMENSIONS

VOLTAGE

24 – 42 VAC

NOTES

Wire Drive

INPUT AMPERES

10A

RATED OUTPUT @ 104°F (40°C)

No Gouging Kit

With Gouging Kit

Wire Drive

Gouging Stud

DUTY CYCLE

60%

30%

INPUT AMPERES

600 Amps

500 Amps

600 Amps

GEARING - WIRE FEED SPEED RANGE-WIRE SIZE

WFS RANGE

50 – 500 inch/min

(1.3 – 12.7 m/min)

50 – 700 inch/min

(1.3 – 19.0 m/min)

.025” – 3/32”

(0.6 – 2.4 mm)

.025” – 1/16”

(0.9 – 1.6 mm)

.035” - .120”

(0.9 – 3.0 mm)

.035 – 5/64”

(0.9 – 2.0 mm)

PINION GEAR

20 tooth

30 tooth

GMAW

FCAW

Thermal tests have been performed at ambient temperature. The Duty Cycle (duty factor) @ 40ºC (104°F) has
been determined by simulation.

= gearing installed in the wire drive as equipped from the factory.

WIRE SIZES

IP2X for the wire drive and user interface.

Содержание FLEX FEED 74 HT




























































Результаты поиска

Содержание FLEX FEED 74 HT

Отзывы:

Бренды по названию

Популярные бренды

Lincoln Electric FLEX FEED 74 HT, Руководство оператора

Результаты поиска

Содержание FLEX FEED 74 HT

Отзывы:

Бренды по названию

Популярные бренды