Lincoln Electric FLEX FEED 74 HT Скачать руководство пользователя

Страница: 31 / 59

A-24

INSTALLATION

FLEX FEED™ 74 HT

SHIELDING GAS CONNECTION

CYLINDER may explode if

damaged.

•Keep cylinder upright and

chained to support.

• Keep cylinder away from areas where it may be

damaged.

• Never lift welder with cylinder attached.

• Never allow welding electrode to touch cylinder.

• Keep cylinder away from welding or other live

electrical circuits.

• BUILD UP OF SHIELDING GAS MAY

HARM HEALTH OR KILL.

• Shut off shielding gas supply when not in

use.

• See American National Standard Z-49.1, "Safety

in Welding and Cutting” Published by the

American Welding Society.

---------------------------------------------------------------

Maximum inlet pressure for the Flex Feed 74 HT is 100
psi. (6.9 bar.)

The inlet fitting is 5/8-18 CGA type connection.

Install the shielding gas supply as follows:
1. Secure the cylinder to prevent it from falling.
2. Remove the cylinder cap. Inspect the cylinder valves

and regulator for damaged threads, dirt, dust, oil or
grease. Remove dust and dirt with a clean cloth. DO
NOT ATTACH THE REGULATOR IF OIL, GREASE

OR DAMAGE IS PRESENT!

Inform your gas supplier

of this condition. Oil or grease in the presence of high
pressure oxygen is explosive.

3. Stand to one side away from the outlet and open the

cylinder valve for an instant. This blows away any dust
or dirt which may have accumulated in the valve outlet.

4. Attach the flow regulator to the cylinder valve and tight-

en the union nut(s) securely with a wrench. Note: if
connecting to 100% CO

cylinder, insert regulator

adapter between regulator and cylinder valve. If
adapter is equipped with a plastic washer, be sure it is
seated for connection to the CO

cylinder.

5. Attach one end of the inlet hose to the outlet fitting of

the flow regulator. Attach the other end to the welding
system shielding gas inlet. Tighten the union nuts with
a wrench.

6. Before opening the cylinder valve, turn the regulator

adjusting knob counterclockwise until the adjusting
spring pressure is released.

7. Standing to one side, open the cylinder valve slowly a

fraction of a turn. When the cylinder pressure gage
stops moving, open the valve fully.

8. The flow regulator is adjustable. Adjust it to the flow

rate recommended for the procedure and process
being used before making a weld.

Содержание FLEX FEED 74 HT




























































Результаты поиска

Содержание FLEX FEED 74 HT

Отзывы:

Похожие инструкции для FLEX FEED 74 HT

Бренды по названию

Популярные бренды

Lincoln Electric FLEX FEED 74 HT, Руководство оператора

Результаты поиска

Содержание FLEX FEED 74 HT

Отзывы:

Похожие инструкции для FLEX FEED 74 HT

Бренды по названию

Популярные бренды