manualshive.com logo in svg

Lincoln Electric FLEX FEED 74 HT, Руководство оператора

Операторам приобретения сварочной машины Lincoln Electric FLEX FEED 74 HT мы предлагаем бесплатное скачивание руководства по эксплуатации на нашем сайте. Руководство оператора доступно для загрузки с manualshive.com. Это незаменимый ресурс для правильного использования и обслуживания вашего оборудования.

Поделиться
Скачать
background image

D-1

MAINTENANCE

SAFETY PRECAUTIONS

ELECTRIC  SHOCK can kill.

• Turn the input power OFF at the welding

power source before installation or changing
drive rolls and/or guides.

• Do not touch electrically live parts.

• When inching with the gun trigger, electrode and drive

mechanism are "hot" to work and ground and could
remain energized several seconds after the gun trigger is
released.

• Do not operate with covers, panels or guards removed or

open.

• Only qualified personnel should perform maintenance

work.

----------------------------------------------------------------------

ROUTINE MAINTENANCE

Check weld cables, control cables and gas hoses for
cuts.

Clean and tighten all weld terminals.

PERIODIC MAINTENANCE

Clean the drive rolls and inner wire guide and replace if
worn.

Blow out or vacuum the inside of the feeder.

Inspect the motor brushes every 6 months.  Replace if
shorter than 0.5” (12.7mm).

CALIBRATION SPECIFICATION

Wire Feed Speed Validation
Calibration matches the scale on the name plate to the
actual wire feed speed.  As shipped from the factory, the
wire feeder is calibration for 0.45 (1.2mm) wire.
Calibration of the Flex Feed™ 74 HT may be required
when the p.c. board, the wire feed speed potentiometer
or the motor is replaced or serviced.

To calibrate the Flex Feed™ 74 HT: 
1. Turn power OFF at the welding power source.
2. Remove the (4) screws holding the roof of the wire

feeder to gain access to the pc board.

3. Turn power ON and trigger the Flex Feed 74 HT. 
4. Set the WFS knob to 50 in/min and measure the drive

roll rpm.  If the drive roll rpm measures 8.9 to 9.2 rpm,
proceed to step 7. 

5. Unplug the connector in J2.  Insert a shorting plug that

shorts pin 1 and 5.  Adjust the WFS knob as required
until drive roll rpm measures:

• 5.93 to 6.13 rpm for 20 tooth pinion gear.
• 8.90 to 9.20 rpm for 30 tooth pinion gear.

6. Remove the shorting plug from J2.
7. Set the WFS knob to 300 in/min.  Measure the drive roll

rpm.  If the drive roll rpm measures 53.97 to 55.17, pro-
ceed to step 10.

8. Unplug the connector in J2.  Insert a shorting plug that

shorts pin 1 and 5.  Adjust the WFS knob as required
until drive roll rpm measures:

• 35.9 to 36.7 rpm for 20 tooth pinion gear.
• 53.97 to 55.17 rpm for 30 tooth pinion gear.

9. Remove the shorting plug from J2.
10. Set the WFS knob to 500 in/min for the 20 tooth pin-

ion gear or 700 in/min for the 30 tooth pinion gear.
Measure the drive roll rpm.  If the drive roll rpm mea-
sures 89.9 to 91.9, proceed to step 13.

11. Unplug the connector in J2.  Insert a shorting plug

that shorts pin 1 and 5.  Adjust the WFS knob as
required until drive roll rpm measures:
• 83.87 to 85.87 rpm for 20 tooth pinion gear.
• 126.32 to 128.32 rpm for 30 tooth pinion gear.

12. Remove the shorting plug from J2.
13. Turn power OFF and reassemble.

WARNING

FLEX FEED™ 74 HT

Содержание FLEX FEED 74 HT




























































Отзывы:

Нет отзывов

Похожие инструкции для FLEX FEED 74 HT

Sola VESTA-2813 NS PLUS User Manual preview
VESTA-2813 NS PLUS
Бренд: Sola Страницы: 80
Schiller Grounds Care RYAN MATAWAY 544283B Operator'S Manual preview
RYAN MATAWAY 544283B
Бренд: Schiller Grounds Care Страницы: 54
Nexus Cardas Audio Instruction preview
Cardas Audio
Бренд: Nexus Страницы: 52

Бренды по названию

Популярные бренды

Загрузить еще бренды