background image

Operating Instructions

O

N

Channel Selection – Handheld T

Channel Selection – Handheld T

Channel Selection – Handheld T

Channel Selection – Handheld T

Channel Selection – Handheld Transmitter

ransmitter

ransmitter

ransmitter

ransmitter

Once a channel has been selected on the receiver, you now need to select that same
channel on the handheld transmitter.  

If you have a belt-pack transmitter, go to

 page 14 

for

channel selection instructions.

ON

LCD

Display

LOCK

SET

HM-900

SET

LOCK

UP

DOWN

Red

LED

ON/OFF

Switch

CH:  002

CH:  002

720.500M

LS

HM-900

SENS SET

LEVEL [2]

NiMH
AKLN

Setup Screens
selectable with

the UP and DOWN

Arrow Buttons

Wireless Transmitter

Handheld Microphone

• Turn the microphone on by sliding

the switch on the barrel to the ON position.  The red LED will flash once.

• To change the channel, press and hold the “SET” button on the bottom of the

microphone until there is a blinking cursor on the LCD display window
(approximately 3 seconds).

• Use the “UP” and “DOWN” Arrows to set the channel to match the receiver.

• Press and hold the “SET” button again until the blinking cursor disappears and the red

LED flashes 

(approximately 3 seconds).

T

TT

TTransmission Frequency in MHz: 

ransmission Frequency in MHz: 

ransmission Frequency in MHz: 

ransmission Frequency in MHz: 

ransmission Frequency in MHz:  Press the “UP”

button once to view the transmission frequency in
MHz of the currently selected channel.

9

NOTE:  Transmitters and receivers
are available in 5 different frequency
groups.  Verify that the letter code that
blinks on the receiver (when powered
ON) matches the letter code on the
frequency sticker in the battery
compartment of the transmitter.

Trouble Shooting Guide

No sound when someone speaks into the wireless microphone:

1.

7100DX system should be plugged into AC power and turned on.  The receiver module
should be set to the same channel as the transmitter.

2.

Microphone/transmitter power should be turned on.  If the LCD display does not
show, the batteries are most likely too weak.  Replace with alkaline batteries.

• If NiMH rechargeable batteries are installed, plug in the charger.  Otherwise,

replace with new alkaline batteries.

If you have gone through this trouble shooting guide and are still having problems, write

down the serial numbers of your system and call the LightSPEED Service Department at

1-800-732-8999

7:00 am - 5:00 pm PST

WARNING: 

 Do not attempt to charge alkaline batteries.  They can overheat

and expand, creating a significant hazard and damaging the transmitter.
(This is not covered by warranty.)

3. Verify the receiver and transmitter are in the same frequency group.

• Turn the receiver module off and on again.  The letter code for the frequency group

will blink.

• Open the battery compartment on the transmitter to find the frequency group sticker.

4. Make sure the Mute light (on the belt-pack transmitter) is not flashing.

The wireless microphone is experiencing drop-out or interference:

1.

The wireless frequency being used may not be a clear channel:

The wireless frequency being used may not be a clear channel:

The wireless frequency being used may not be a clear channel:

The wireless frequency being used may not be a clear channel:

The wireless frequency being used may not be a clear channel:  Turn the transmit-
ter off and press the SCAN button on the receiver to find a clear frequency.  Then
make sure to select the same channel on the transmitter.

2.

Squelch adjust on the receiver is set too high:

Squelch adjust on the receiver is set too high:

Squelch adjust on the receiver is set too high:

Squelch adjust on the receiver is set too high:

Squelch adjust on the receiver is set too high:  If this squelch is set too high (fully
clockwise), this can drastically reduce the range of the transmitter, resulting in more
frequent dropout.

3.

Squelch adjustment is set too low:

Squelch adjustment is set too low:

Squelch adjustment is set too low:

Squelch adjustment is set too low:

Squelch adjustment is set too low:  In areas of severe interference (large downtown
urban areas, airports, military bases, etc) it may be necessary to turn the squelch
up slightly to avoid outside interference.

4.

TTTTTransmitter is out of range of receiver:

ransmitter is out of range of receiver:

ransmitter is out of range of receiver:

ransmitter is out of range of receiver:

ransmitter is out of range of receiver:      The transmitters do have a maximum range

of about 300-350 feet in an open field environment.  This range can be dramatically
reduced indoors and when large objects (such as a wall) may be obstructing the
path directly between transmitter and receiver.  If this is the case, it may be
necessary to position the two closer together.

5.

Batteries are ver

Batteries are ver

Batteries are ver

Batteries are ver

Batteries are very weak:

y weak:

y weak:

y weak:

y weak:      Right before the batteries are about to die, it can

drastically affect the overall performance of the system.  Make sure to check the
battery status of the transmitter (belt-pack or handheld).

18

• Use the “up” and “down” buttons to select a screen that shows the current channel.

CH:  002

720.500M

Содержание 7100DX QUAD-RAK




























Отзывы: