Page 8 of 13
SC910D/SC910W DMX CONTROLLER
Version 2.1
OWNERS MANUAL
11/02/2020
www.lightronics.com
Lightronics Inc.
509 Central Drive Virginia Beach, VA 23454
757 486 3588
ACCESSING AND SETTING FUNCTIONS
1. Hold down REC for more than 3 seconds. The REC
light will begin blinking.
2. Push CHN MOD. The CHN MOD and REC lights
will blink alternately.
3. Enter a 2 digit function code using the scene buttons
(1 - 8). The scene lights will flash a repeating pattern of
the code entered. The unit will return to its normal
operating mode after about 20 seconds if no code is
entered.
4. Push CHN MOD. The CHN MOD and REC lights
will be ON. The scene lights (in some cases including
the OFF(0) and BNK(9) lights) will show the current
function setting or value.
Your action now depends on which function was
entered. Refer to the instructions for that function. You
can enter new values and push REC to save them or push
CHN MOD to exit without changing the values. At this
point, the unit will return to its normal operation mode
after 60 seconds if no function settings are entered.
SETTING FADE TIMES
(Function Codes 11 - 32)
The fade time is the minutes or seconds to move
between scenes or for scenes to go ON or OFF. The
fade time for each scene can be individually set. The
SC910 pushbuttons are Scenes 1-8, Scenes 9-16
correlate to SC910 faders 1-8, however the fade time
settings is only applicable to the use of either push
button smart remotes or simple remotes assigned to
Scene 9-16. The allowable range is from 0 seconds to 99
minutes.
Fade time is entered as 4 digits and can be either minutes
or seconds. Numbers entered from 0000 - 0099 will be
recorded as seconds. Numbers 0100 and larger will be
recorded as even minutes and the last two digits will not
be used. In other words; seconds will be ignored.
After accessing a function (11 - 32) as described in
ACCESSING AND SETTING FUNCTIONS:
1. The scene OFF(0) and BNK(9) lights will be
flashing a repeating pattern of the current fade time
setting.
2. Use the scene buttons to enter a new fade time (4
digits). Use OFF for 0 and BNK for 9 if needed.
3. Push REC to save the new function setting.
Function Code 32 is a master fade time function which
will set ALL fade times to the value entered. You can
use this for a base setting for fade times and then set
individual scenes to other times as needed.
SIMPLE REMOTE SWITCH BEHAVIOR
The SC910 is very versatile in how it can respond to the
simple remote switch inputs. Each switch input can be
set to operate according to its own settings.
Most settings pertain to momentary switch closures.
The MAINTAIN setting allows the use of a regular
ON/OFF switch. When used this way, the applicable
scene(s) will be ON while the switch is closed and OFF
when the switch is open.
Other scenes can still be activated and the OFF button
on the SC910 will turn the MAINTAIN scene off. The
switch must be cycled off then on to reactivate the
MAINTAIN scene.
SETTING SIMPLE SWITCH INPUT OPTIONS
(Function Codes 33 - 35)
After accessing a function (33 - 35) as described in
ACCESSING AND SETTING FUNCTIONS:
1. The scene lights including OFF(0) and BNK(9) will
flash a repeating pattern of the current setting.
2. Use the scene buttons to enter a value (4 digits).
Use OFF for 0 and BNK for 9 if needed.
3. Push REC to save the new function value.
The function values and description are as follows:
SCENE ON/OFF CONTROL
0101 - 0116 Turn ON Scene (01-16)
0201 - 0216 Turn OFF Scene (01-16)
0301 - 0316 Toggle ON/OFF Scene (01-16)
0401 - 0416 MAINTAIN Scene (01-16)
