manualshive.com logo in svg
background image

 
 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  Page 11 of 13 

SC910D/SC910W DMX CONTROLLER 

Version 2.1   

 

 

 

 

 

 

 

 

   

OWNERS MANUAL  

 

 

 

 

 

 

 

 

 

    11/02/2020 

www.lightronics.com 

Lightronics Inc.   

 

 

 

 

 

 

 

 

509 Central Drive Virginia Beach, VA 23454  

 

 

 

 

 

   757 486 3588 

Scene activated does not appear to be what was stored.  

-Verify all DMX connections are made securely.  
-Confirm  the  DMX  polarity  for  each  connection  is 

correct.  
-Check that the scene has not been recorded over by re-
creating the scene on the  SC910 or DMX console and 
re-recording. 
 
SC910 not responding to remote stations. 
-Verify  all  smart  remote  station  connections  are  made 
securely on SC910 and remote stations. 
-Verify  continuity  of  wiring  between  SC910  and  wall 
stations.  
-Verify  wall stations are daisy  chained and  not  in star 
configuration.  
-Verify  there  is  12  VDC  minimum  from  pin  9  of  the 
DB9 connector on the SC910. 
-Verify  Remote  Station  Lockouts  are  not  active  on 
SC910 
-Verify Fader Station Starting Scene settings. 
  
Some  dimmers  or  fixtures  are  not  responding  to  the 
SC910. 
- Make sure the dimmer/fixtures’ addresses are set to the 
proper DMX channels.  
-Make sure the DMX daisy chain is wired properly and 
terminated. 

  

CLEANING  

  

The best way to prolong the life of your SC910 is to 
keep it dry, cool, and clean.  

  

COMPLETELY DISCONNECT THE UNIT BEFORE 

 

CLEANING AND MAKE SURE IT IS COMPLETELY 

 

DRY BEFORE RECONNECTING.

 

  

The unit exterior may be cleaned using a soft cloth 
dampened with a mild detergent/water mixture or a 
mild spray-on type cleaner.  DO NOT SPRAY ANY 
LIQUID directly on the unit.  DO NOT IMMERSE the 
unit in any liquid or allow liquid to get into the fader or 
push button controls.  DO NOT USE any solvent based 
or abrasive cleaners on the unit.  

  

REPAIRS  

    

There are no user serviceable parts in the SC910.  
Service by anyone other than Lightronics authorized 
agents will void your warranty.  

 

OPERATING AND TECHNICAL ASSISTANCE  

  

Your local dealer and Lightronics factory personnel 
can help you with operation or maintenance problems.  
Please read the applicable parts of this manual before 
calling for assistance.  

  

If service is required - contact the dealer from whom 
you purchased the unit or contact Lightronics directly. 
Lightronics, Service Dept., 509 Central Dr., Virginia 
Beach, VA   23454   TEL:  (757) 486-3588.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 

Содержание SC910D















Отзывы: