Programming Modules
Programming a DM or NDM
Creating Scenes with One or Multiple Modules
1.
Press and hold the Laser button and aim laser
beam at an individual modules receiver to select it
and place it in program mode. (When using multiple
modules, select them in the same manner if they need
to be programmed identically to the first module.)
The module’s LED(s) will blink at a 1/2 second rate
when in program mode. The LRC’s LED will also blink
(every 1 second) to indicate the transmitter will be
transmitting program IR commands when buttons are
depressed. (After 60 seconds of inactivity, the mod-
ule(s) will exit the program mode without saving.)
2.
Press a SCENE button to be programmed (
A B
C D E F
ON
or
OFF
). The module(s) will start to
fade to the current scene level (the default fade rate
for all scenes is 3 sec).
NOTE:
For the OFF Scene, only the fade rate can be
changed, not the light level.
NOTE:
The NDM will switch to full light output and will
not fade.
3.
Press the LRC’s up
or down button’s for the
desired light level setting for the scene. If you only
want to change the fade rate, skip this step.
4.
To change the fade rate for the selected scene, press
the Fade
f
button. Press the Fade
f
button again
for a 1 1/2 sec fade or one of the TIME buttons
(
3 7 15 30
sec.
,
5
or
30
min.).
If you don’t want to change the fade rate, skip this
step.
5.
Repeat steps 2 through 5 for all scenes you want to
program.
6.
To exit the program mode and
SAVE
the parameters
you have just set, press the Learn button. To exit
the program mode and
CANCEL
any parameters you
just set, press the end
e
button. The selected
module(s) LED(s) will stop blinking indicating that you
are no longer in program mode.
NOTE
: If using a TM that is in the LRC’s viewing angle,
all modules that have the same address as the TM will
respond to scene changes.
Testing a TM
1.
Turn off power to track.
2.
Install modules into track with luminaire attached
(See Section 3 – Installation of Modules to Lytespan
Track Systems). Install TM into track. Re-power Track.
3.
Using the LRC, press and hold the Learn
button
for 2 seconds which turns on the TM’s LED so it can
be easily located.
4.
Press and hold the Laser
button and aim laser
beam at the TM’s receiver to select it and place it in
program mode. The TM’s LED(s) will blink at a 1/2
second rate when in program mode. The LRC’s LED
will also blink (every 1 second) to indicate the
transmitter will be transmitting program IR commands
when buttons are depressed. (After 60 seconds of
inactivity, the module(s) will exit the program mode
without saving.)
5.
Point the handheld LRC transmitter in the general
direction of the TM and press a SCENE button
A B
C D E F
ON
or
OFF
. If the module’s respond to
these buttons with changes in light levels, the TM is
working.
6.
Press the end
e
button to exit the program mode.
6. Programming ATOM (Basic)
Quick Tips:
Easily Locating Modules on Ceiling or Wall
1.
The Modules LED’s can be turn on so they can be
located easily on the ceiling or wall:
a) To have the LED(s) blink on, press the Learn
button.
b) To have the LED(s) stay on for 60 seconds, press
and hold the Learn
button for 2 seconds.
NOTE:
When using a TM, pointing the LRC at the TM
and performing step 1a above will cause all of the
Module’s LED’s on its address to blink on.
Note: DM’s and TM’s have red LED’s and NDM’s have
green LED’s.
This can be done anytime the Modules aren’t in
program mode. It is recommend to do this before
programming so all Modules can be located easily and
there is a target to aim the laser.
Forcing A Fade:
DM’s will always fade into and out of a scene. The
default fade rate for all fades is 3 seconds but can be
set to as long as 30 minutes or as short as 1 1/2 sec-
onds. If a scenes fade rate is long, you can press the
Fade
f
button to force a fast fade into the scene.
12
13
