background image

If you want to program a, DM or NDM’s address to
match the address of a TM, WRC, or a Compose

CP

Master, perform the following steps:
a)

To program the modules address to match a TM’s 
address, aim the LRC in the direction of the module 
and press any of the SCENE buttons (  

A    B    C    D 

E  

or  

F  

) (this puts the modules in address search 

mode which looks for another units address) and wait
two seconds. Aim the LRC in the direction of the TM 
and press the Cycle   

c

button. Advance to step 4.

b)

To program the modules address to match a WRC or 
Compose CP Master Unit’s address, aim the LRC in 
the direction of the module and press any of the 
SCENE buttons (  

A    B    C    D    E  

or

F  

) (this puts 

the modules in address search mode which looks for 
another units address) and wait two seconds.     
Press any SCENE button (

A, B, C, D, ON, 

or 

OFF

) on 

the WRC or CP Master Unit. Advance to step 4.

If you want to program a TM’s address to match the
address of a WRC or Compose CP Master.

Point the LRC at the TM and press any of the SCENE
buttons (  

A    B    C    D    E 

or

) (this puts the

modules in address search mode which looks for 
another units address) and wait two seconds. Press any
SCENE button (

A, B, C, D, ON, 

or 

OFF

) on the WRC or

CP Master Unit. Advance to step 4.

4.

To exit the program mode and 

SAVE

the parameters 

you have just set, press the Learn 

button. To exit 

the program mode and 

CANCEL

any parameters you 

just set, press the end   

e

button. The selected

modules) LED(s) will stop blinking indicating that you 
are no longer in program mode.

NOTE:

To do a check to see what modules are on the

TM’s address, see Globally Select Modules with TM
from section 6. All of the modules that go into program
mode are on the same address as the TM.

Address Programming for a WRC

1.

On the WRC, press and hold the

B

and 

E

buttons for   

3 seconds. The 

Cycle

button will blink and the house 

address will be displayed on the remaining buttons.

2.

Press the 

B

button multiple times until only the 

End

button is lit. You are now at House A. 

3.

Press the 

A

button to select House B.

4.

Press the 

A

button again to select House C. Continue 

this sequence until the desired House is selected.

5.

Press the 

Cycle

button. You will now select the unit 

number.

6.

Press the 

B

button until only the 

End

button is lit  

(This is done the same way as in step 2).                
You are now at Unit 1.

7.

Press the 

A

button to select Unit 2.

8.

Press the 

A

button again to select Unit 2. Continue 

this sequence until the desired unit is selected.

9.

Press the 

Cycle

button to exit and save the address 

settings.

The module’s LED(s) will blink at a 1/2 second rate 
when in program mode. The LRC’s LED will also 
blink(every 1 second) to indicate the transmitter will 
be transmitting program IR commands when buttons 
are depressed. (After 60 seconds of inactivity, the 
module(s) will exit the program mode without saving.)

2.

Press and hold the Begin  

b

button for greater than 

3 seconds (the module’s LED(s) will blink rapidly and 
then after 3 seconds stay on). Release the Begin   

b

button. The module’s LED(s) will blink at a 1/4 second 
rate. (After 60 seconds of inactivity, the module(s) will 
exit the program mode without saving.)

3.

To 

Enable

the IR, press the  

ON

button. To 

Disable

the

IR, press the  

OFF

button.

4.

To exit the program mode and 

SAVE

the parameters 

you have just set, press the Learn   

button. To exit 

the program mode and 

CANCEL

any parameters you 

just set, press the end   

e

button. The selected

modules) LED(s) will stop blinking indicating that you 
are no longer in program mode.

Address Programming for DM, NDM & TM

Addressing allows you to set and address individual
modules to run several completely separate ATOM 
systems on the same track. The Factory Default for the
DM, NDM,  & TM’s Address is ‘C1’.  This allows all units
to communicate "out of the box" with out any 
addressing. A TM will only operate with a DM, NDM, or
WRC that match its same address. All modules,TM’s, &
WRC’s have the same address when shipped from the
factory. If a change in address is desired: 

1.

Press and hold the Laser  

button and aim laser 

beam at an individual modules receiver to select it 
and place it in program mode. (When using multiple 
modules, select them in the same manner if they need
to be programmed identically to the first module.) The 
module’s LED(s) will blink at a 1/2 second rate when in
program mode. The LRC’s LED will also blink (every 1 
second) to indicate the transmitter will be transmitting
program IR commands when buttons are depressed. 
(After 60 seconds of inactivity, the module(s) will exit 
the program mode without saving.)

2.

Press and hold the Begin  

b

button for greater than 

3 seconds (the module’s LED(s) will blink rapidly and 
then after 3 seconds stay on). Release the Begin  

b

button. The module’s LED(s) will blink at a 1/4 second 
rate. (After 60 seconds of inactivity, the module(s) will 
exit the program mode without saving.)

3. If you know what address you want to program a 

DM, NDM, or TM, press the following with the LRC:

a)

A

– for address C1 – House "C", Unit "1"

b)

B

– for address C2 – House "C", Unit "2"

c)

C

– for address C3 – House "C", Unit "3"

d)

D

– for address C4 – House "C", Unit "4"

e)

E

– for address C5 – House "C", Unit "5"

f )

F

– for address C6 – House "C", Unit "6"

Advance to step 4

18

19

Содержание Atom Lytespan CAM250VA
















Отзывы: