Life Fitness Exercise Bike Lifecycle 8500 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 35

background image

STEP 8:

FIGURE 8

11

• Slide two HINGE TABS (76) onto the WOLFF SLEEVE (14) and

SECURELY

attach PRESS SEAT PAD (100) using two 3/8 X 1-1/4”

BOLTS (88) and two 3/8” WASHERS (80).

(NOTE: The “hinge” part of the HINGE TAB (76) should face upward as shown in

FIGURE 8.)

• Slide the RIGHT BACK PAD ANGLE (5) and LEFT BACK PAD ANGLE (4) onto the WOLFF SLEEVE (14) and attach the PRESS

BACK PAD (101) using four 3/8 X 1-1/4” BOLTS (88) and four 3/8” WASHERS (80). See FIGURE 8.

•

SECURE

two 2 X 15-1/2” PLATES (56) to the RIGHT BACK PAD ANGLE (5) and the LEFT BACK PAD ANGLE (4) using two 1/2 X 1-

1/4” BOLTS (93), two 1/2” WASHERS (84) and two 1/2” LOW HEIGHT LOCK NUTS (86).

(NOTE: SECURE lock nuts, then back off

1/4 turn.)

•

SECURE

the 2 X 15-1/2” PLATES (56) to the bushing in the PRESS BASE (38) using one 1/2 X 6-1/2” BOLT (97) and one 1/2” LOCK NUT

(85) as shown in FIGURE 8.

• Apply one 1-1/4” RUBBER BUMPER (54) to the PRESS FRAME (37) where the back of the pad comes in contact with the frame.

4

5

80

54

37

85

100

14

76

80

84

1/2 X 1-1/4” 93

3/8 X 1-1/4” 88

116

86

101

3/8 X 1-1/4” 88

1/2”

LOW

HEIGHT

38

97 1/2 X 6-1/2”

«
...
9
10
11
12
13
...
»

Содержание Exercise Bike Lifecycle 8500




































Отзывы:

Нет отзывов

Похожие инструкции для Exercise Bike Lifecycle 8500

Бренд: PowerPeak Страницы: 84

Бренд: Tunturi Страницы: 14

Бренд: Pro-Form Страницы: 28

Бренд: Octane Fitness Страницы: 24

Бренд: Octane Fitness Страницы: 40

Бренд: Domyos Страницы: 33

Бренд: York Fitness Страницы: 20

890e W/hand Pulse

Бренд: ProForm Страницы: 16

Бренд: ProForm Страницы: 16

485 E Eng/french

Бренд: ProForm Страницы: 16

Momentum 7.0 Ex Elliptical

Бренд: Weslo Страницы: 16

Бренд: VIRTUFIT Страницы: 28

Бренд: Vision Fitness Страницы: 44

Бренд: Vision Fitness Страницы: 58

ASTRORIDE A4.0 BIKE

Бренд: Reebok Страницы: 15

Бренд: Reebok Страницы: 18

Бренд: Reebok Страницы: 28

Бренд: Reebok Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды