Life Fitness Exercise Bike Lifecycle 8500 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 35

background image

STEP 10:

13

•

SECURELY

assemble one 1/2 X 3-1/2” SPRING PIN (63) to the PRESS ARM (8) as shown in FIGURE 10.

FIGURE 10

•

SECURELY

assemble the PRESS ARM (8) to the PRESS ARM ADJUST (36) using one 1/2 X 7-1/2” BOLT (98), two 1/2” WASHERS (84),

two 1/2” FLANGE BEARINGS (70), and one 1/2” LOW HEIGHT LOCK NUT (86).

(NOTE: SECURELY tighten, then back nut off 1/4

to allow the PRESS ARM to rotate freely.)

63

8

70

36

86 1/2” LOW HEIGHT

98 1/2 X 7-1/2”

84

82

90 3/8 X 2-3/4”

•

SECURELY

assemble four 3/8 X 2-3/4” BOLTS (90) and four 3/8” LOCK NUTS (82) to the PRESS ARM ADJUST (36) as sjown in FIGURE 10.

«
...
11
12
13
14
15
...
»

Содержание Exercise Bike Lifecycle 8500




































Отзывы:

Нет отзывов

Похожие инструкции для Exercise Bike Lifecycle 8500

Бренд: York Fitness Страницы: 36

Бренд: U.N.O Fitness Страницы: 45

Бренд: Vision Fitness Страницы: 3

Бренд: Nautilus Страницы: 12

Бренд: Nautilus Страницы: 24

Бренд: Energetics Страницы: 62

Бренд: Gravity Walker Страницы: 10

Бренд: U.N.O Fitness Страницы: 52

Бренд: Landice Страницы: 16

675 Cardio CrossTrainer

Бренд: Pro-Form Страницы: 16

Бренд: Pro-Form Страницы: 24

7.0 Re Elliptical

Бренд: Pro-Form Страницы: 28

Skier Plus WLUVSK10160

Бренд: Weslo Страницы: 6

Бренд: Weslo Страницы: 16

Бренд: Weslo Страницы: 16

Бренд: Weslo Страницы: 16

Momentum 900 Fm

Бренд: Weslo Страницы: 16

Бренд: Weslo Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды