LG UU24WD Скачать руководство пользователя страница 24

Страница: 24 / 44

Air Conditioner

Remote Controller Installation

Remote Controller Installation

Install the remote control box and cord correctly.

• Although the room temperature sensor is in the indoor unit, the remote control box should

be installed in such places away from direct sunlight and high humidity.

INSTALLATION OF THE REMOTE CONTROL BOX

• Select places that is not splashed by water.
• Select control position after receiving

customer approval.

• The room temperature sensor of the

thermostat for temperature control is built in
the indoor unit.

• This remote controller equipped with liquid

crystal display. If this position is higher or
lower, display is difficult to see.
(The standard height is 1.2~1.5m high)

ROUTING OF THE REMOTE CONTROL CORD

• Keep the remote control cord away from

the refrigerant piping and the drain piping.

• To protect the remote control cord from

electrical noise, place the cord at least 5cm
away from other power cables. (Audio
equipment, Television set, etc)

• If the remote control cord is secured to a

wall, provide a trap at the top of the cord to
prevent water droplets from running.

POINT OF REMOTE CONTROLLER INSTALLATION

DISASSEMBLING OF THE REMOTE CONTROLLER

ELECTRICAL WIRING TO THE INDOOR UNIT

Make sure that wire and terminal
numbers are matched on unit side
and remote controller side.

(Main board)

CN REMO

The maximum length of the cord is 100m. If the length of the cord exceeds 50m, use a wire size greater than 0.5mm

Remote controller

CN REMO

Remote

control

box body

Lever carefully

the box open

using a screw

driver, etc.

Front case

The lower part

Face of wall

Upper notch

Upper flange

Under plate

Remote

control cord

Remote

control unit

Tapping screw

(Local supply)

Lower notch

Face of wall
Upper notch

Lower notch
Switch box

(Local supply)

Under plate
Remote

control unit

Remote

control cord

Screw

(Local supply)

Cord

clamp

Push hand

(Part B)

(Part A)

FIXING OF REMOTE
CONTROL CORD

1. Fix the cord clamps on the wall

by ø3 tapping screws(Local supply).

2. Fix the remote control cord.

PROCEDURE OF INSTALLATION

1. Fix the under plate on the switch box by

screws(Local supply). In this case, fit the under
plate on the wall, and be careful of deformation.

2. Receive the remote control cord in the switch box.
3. Hook the remote control unit on the under plate.

WHEN THE REMOTE CONTROL BOX IS

INSTALLED WITH THE CORD BURIED.

PROCEDURE OF INSTALLATION

1. Fix the under plate on the wall by self tapping

screws (accessory).

2. Make a slit (Part A) at the top side of the remote

control box by nipper.

3.Rout the cord as shown in the following figure. In

this case, push the cord into the around of
case(Part B).

4. Hook the remote control unit on the under plate.

WHEN THE REMOTE CONTROL BOX IS
INSTALLED WITH THE CORD EXPOSED.

installation of remote control box

Содержание UU24WD













































Результаты поиска

Содержание UU24WD

Отзывы:

Похожие инструкции для UU24WD

Бренды по названию

Популярные бренды

LG UU24WD, Руководство по установке

Результаты поиска

Содержание UU24WD

Отзывы:

Похожие инструкции для UU24WD

Бренды по названию

Популярные бренды