LG UU24WD Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 44

background image

30

Air Conditioner

Installation to Decorative Panel

1. Temporarily fix two decoration panel fixing screws (hexagon M5 screw) on the unit body.

(Tighten by amount 10mm in length.)
The fixing screws (hexagon M5 screw) are included the indoor unit box.

2. Remove the air inlet grille from the decoration panel. (Remove the hook for the air inlet grille cord.)
3. Hook the decoration panel key hole ( ) on the screws fixed in step above, and slide

the panel so that the screws reach the key hole edge.

4. Retighten completely two temporarily fixed screws and other two screws. (Total 4 screws)
5. Connect the louver motor connector and display connector.
6. After tightening these screws, install the air inlet grille (including the air filter).

Decoration panel fixing screws
(hexagon M5 screws)
Temporally fitting at 2 places
(Tightening about 10mm)

Air conditioner unit

Decoration panel

Control box cover

Piping side

Louver motor

Display

Lead wire for
louver motor and
display

Inlet Grille

Decoration panel fixing screws

Decoration panel fixing screws
(Hexagon M5 screw)

(Hexagon M5 screw)

Decoration panel fixing screws
(Hexagon M5 screw)

The decoration panel has its
installation direction.

Before installing the decoration panel,
always remove the paper template.

Installation to Decorative Panel

Air conditioner
unit

Ceiling

board

Decoration panel

Decoration
panel

Fit the insulator (this part) and
be careful for cool air leakage

Good example

Air

Cool air leakage

(no good)

Bad example

Ceiling

board

Air conditioner unit

CAUTION : Install
certainly the
decoration panel.
Cool air leakage
causes sweating.

Water drops fall.

«
...
28
29
30
31
32
...
»

Содержание UU24WD













































Отзывы:

Нет отзывов

Похожие инструкции для UU24WD

Бренд: Vax Страницы: 7

Бренд: Jaga Страницы: 12

Бренд: Daikin Страницы: 7

Бренд: Daikin Страницы: 6

Бренд: Daikin Страницы: 24

Бренд: Daikin Страницы: 28

Бренд: Daikin Страницы: 34

Бренд: Daikin Страницы: 44

Бренд: Daikin Страницы: 44

Бренд: Daikin Страницы: 13

Бренд: Daikin Страницы: 22

Бренд: Daikin Страницы: 134

Бренд: Daikin Страницы: 274

Бренд: Daikin Страницы: 16

HSU24VHG(DB)-G&W

Бренд: Haier Страницы: 98

Бренд: RollSeal Страницы: 44

Бренд: O3ZY Страницы: 15

Бренд: Perfect Aire Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды