LG UU24WD Скачать руководство пользователя страница 15

Страница: 15 / 44

The Indoor Unit Installation

Installation Manual

ENGLISH

MOUNTING THE ANCHOR NUT AND
BOLT

• Prepare 4 suspension bolts. (Each bolts length

should be same.)

• Measure and mark the position for the

Suspension bolts and the piping hole.

• Drill the hole for anchor nut on the ceiling.

• Insert the nuts and washer onto the

suspension bolts for locking the suspension
bolts on the ceiling.

• Mount the suspension bolts to the anchor-nuts

firmly.

• Secure the hangers onto the Suspension bolts

(adjust level roughly.) using nuts, washers and
spring washers.

• Adjust a level with a level gauge on the

direction of left-right, back-forth by adjusting
suspension bolts.

• Adjust a level on the direction of top-bottom by

adjusting supension bolts. Then the unit will be
declined to the bottomside so as to drain well.

Suspension bolt

Washer

Nut

Suspension

bolts

Ceiling

Anchor nut

Suspension

bolts

Spring
washer

Max.

12mm

Hangen

Washer

Nut

Flat washer for M10

(accessory)

Flat washer for M10

(accessory)

Hanging bolt

(W3/8 or M10)

Nut
(W3/8 or M10)

Nut

(W3/8 or M10)

Spring washer

(M10)

: Tighten the nut and bolt to prevent unit

falling.

CAUTION

DRILL A HOLE IN THE WALL.

• Drill the piping hole with a ø70mm hole core

drill. Drill the piping hole at either the right or
the left with the hole slightly slanted to the
outdoor side.

5-7mm

(3/16"~5/16")

Indoor

WALL

Outdoor

1655

320

1255

320

855

320

DIM.

MODEL

Содержание UU24WD













































Результаты поиска

Содержание UU24WD

Отзывы:

Похожие инструкции для UU24WD

Бренды по названию

Популярные бренды

LG UU24WD, Руководство по установке

Результаты поиска

Содержание UU24WD

Отзывы:

Похожие инструкции для UU24WD

Бренды по названию

Популярные бренды