LG U970 Скачать руководство пользователя страница 66

Страница: 66 / 210

3. TECHNICAL BRIEF

- 67 -

3.11.9.1. Audio Signal Processing & Interface

Audio signal processing is divided uplink path and downlink path.

The uplink path amplifies the audio signal from MIC and converts this analog signal to digital signal

and then transmits it to DBB Chip (MSM6280).

This transmitted signal is reformed to fit in GSM & WCDMA frame format and delivered to RF Chipset.

The downlink path amplifies the signal from DBB chip (MSM6280) and outputs it to receiver (or

speaker).

The receive path can be directed to either one of two earphone amplifiers or the auxiliary output. The

outputs earphone1 (EAR1OP, EAR1ON) and auxiliary out (LINE_OP, LINE_ON) are differential

outputs. Earphone2 (HPH_L, HPH_R) is a single-ended output stage designed to drive a headset

speaker. The microphone interface consists of two differential microphone inputs, one differential

auxiliary input and a two-stage audio amplifier.

Figure. Audio Interface Detailed Diagram(MSM6280)

Содержание U970



















































































































































































































Результаты поиска

Содержание U970

Отзывы:

Похожие инструкции для U970

Бренды по названию

Популярные бренды

LG U970, Руководство по обслуживанию

Результаты поиска

Содержание U970

Отзывы:

Похожие инструкции для U970

Бренды по названию

Популярные бренды