LG U970 Скачать руководство пользователя страница 36

Страница: 36 / 210

3. TECHNICAL BRIEF

- 37 -

3.8. Subsystem(MSM6280)

3.8.1. ARM Microprocessor Subsystem

The MSM6280 device uses an embedded ARM926EJ-S microprocessor. This microprocessor,

through the system software, controls most of the functionality for the MSM, including control of the

external peripherals such as the keypad, LCD, SDRAM, and NAND-Flash devices. Through a

QUALCOMM proprietary serial bus interface (SBI) the ARM926EJ-S configures and controls the

functionality of the RTR6275, RFR6275 and PM6650 devices.

3.8.2. WCDMA R99 features

The MSM6280 device supports release 99 June 2004 of the W-CDMA FDD standard, including the

following features:

• All modes and data rates for W-CDMA frequency division duplex (FDD), with the following

restrictions:

• The downlink supports the following specifications:

- Up to four physical channels, including the broadcast channel (BCH), if present

- Up to three dedicated physical channels (DPCHs)

- Spreading factor (SF) range support from 4 to 256

- The following transmit diversity modes are supported:

Space time transmit diversity (STTD)

Time-switched transmit diversity (TSTD)

Closed-loop feedback transmit diversity (CLTD)

• The uplink supports the following specifications:

• The uplink provides the following UE support:

- One physical channel, eight TrCH, and 16 TrBks starting at any frame boundary

- A maximum data rate of 384 kbps

• Full SF range support from 4 to 256

• SMS (CS and PS)

• PS data rate - 384 kbps DL / 384 kbps UL

• CS data rate - 64 kbps DL / 64 kbps UL

• AMR (all rates)

3.8.3. HSDPA features

The MSM6280 device supports the HSDPA release 5 standard:

• Supports HS-DSCH (HS-SCCH, HS-PDSCH and HS-DPCCH) in addition to the R99 transport

channels as defined in 3GPP specifications.

• Supports a maximum of four simultaneous HS-SCCH channels as defined in 3GPP specifications.

• Supports a maximum of 10 HS-PDSCH channels and supports both QPSK and 16 QAM modulation.

It supports UE category 6 in SW release 2.0 and category 8 in SW release 4.0.

• Supports CQI, and ACK/NACK on HS-DPCCH channel as defined in 3GPP specifications.

• Supports all incremental redundancy versions for HARQ, as defined in 3GPP specifications.

Содержание U970



















































































































































































































Результаты поиска

Содержание U970

Отзывы:

Похожие инструкции для U970

Бренды по названию

Популярные бренды

LG U970, Руководство по обслуживанию

Результаты поиска

Содержание U970

Отзывы:

Похожие инструкции для U970

Бренды по названию

Популярные бренды