LG U970 Скачать руководство пользователя страница 38

Страница: 38 / 210

3. TECHNICAL BRIEF

- 39 -

3.8.6. EDGE features

• EDGE E2 power class for 8 PSK

• DTM (simple Class A), multi-slot class 12

• Downlink coding schemes - CS 1-4, MCS 1-9

• Uplink coding schemes - CS 1-4, MCS 1-9

• BEP reporting

• SRB loopback and test mode B

• 8-bit, 11-bit RACH

• PBCCH support

• 1 phase/2 phase access procedures

• Link adaptation and IR

• NACC, extended UL TBF.

3.8.7. MSM6280 device audio processing features

• Integrated wideband stereo CODEC

- 16-bit DAC with typical 88 dB dynamic range

- Supports sampling rates up to 48 kHz on the speaker path and 16 kHz on the microphone path

• VR- Voice mail + voice memo

• Acoustic echo cancellation

• Audio AGC

• Audio Codecs: AMR-NB, AAC, AAC Plus, Enhanced AAC Plus, Windows Audio v9, Real Audio 8

(G2)

• Internal vocoder supporting AMR, FR, EFR, and HR

3.8.8. MSM6280 microprocessor subsystem

• Industry standard ARM926EJ-S embedded microprocessor subsystem

- 16 kB instruction and 16 kB data cache

- Instruction set compatible with ARM7TDMI®

- ARM version 5TEJ instructions

- Higher performance 5 stage pipeline, Harvard cached architecture

- Higher internal CPU clock rate with on-chip cache

• Java hardware acceleration

• Enhanced memory support

Please note that NOR/PSRAM will not be supported on MSM6280.

- 75 MHz and 90 MHz bus clock for SDRAM

- 32-bit SDRAM

- Dual memory buses separating the high-speed memory subsystem (EBI1) from low-speed

peripherals (EBI2) such as LCD panels

- 1.8 V or 2.6 V memory interface support (excluding EBI1)

- NAND FLASH memory interface

Содержание U970



















































































































































































































Результаты поиска

Содержание U970

Отзывы:

Похожие инструкции для U970

Бренды по названию

Популярные бренды

LG U970, Руководство по обслуживанию

Результаты поиска

Содержание U970

Отзывы:

Похожие инструкции для U970

Бренды по названию

Популярные бренды