LG Multi V ARUN100LM3 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 81

LG Multi V ARUN100LM3 Скачать руководство пользователя страница 59

Integrated Test Running Function_Cooling Mode (Setting 3)

This function is checking process for normal operation of parts and system On operating system.
• All processes carry out included refrigerant amount judge logic and check normal condition of parts on cooling
mode.
• This function check only normal condition of parts on heating mode.
• Saved data can check using LGMV.

Note

1. Judge the normal condition refer to report of Test Running.

Start

Temp. Condition

1 IDU operation

(All-1) IDU operation

System off

All IDU operation

(refrigerant check)

Error Display

Error Display

Press black button for 2 sec

End

Press the black button for 2 sec.
after turning off all of Dip switch.

Completed

All IDU operation on

Fan mode

Press the black button for 2 sec

Test Run

DIP Switch Settings

Warning

: Please reset Main PCB before starting this function

ENGLISH

Installation Manual

59

«
...
57
58
59
60
61
...
»

Содержание Multi V ARUN100LM3


















































































Отзывы:

Нет отзывов