LG Multi V ARUN100LM3 Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 81

LG Multi V ARUN100LM3 Скачать руководство пользователя страница 47

Electrical Wiring

n

Setting the DIP switch

• Heat pump

• If you set the Dip switch when power is on, the changed setting will not be applied immediately.

The changed setting will be enabled only when Power is reset or by pressing Reset button.

CAUTION

1. ʻXʼ mark within the table means that the dip switch must be pulled down. If not, the function may not work properly.
2. If the applicable dip switch is not set properly, the product may not work properly.
3. When executing the test operation, check the operating condition of the indoor unit and only execute the operation

when all indoor units are stopped.

4. Auto test operation function does not work for the product where only one indoor unit is connected for use.

ENGLISH

Installation Manual

47

Index

1

2

3

4

5

6

7

8

9

10

11

12

13

14

Function

Auto charging

● ●

●

ⅹ ⅹ

Refrigerant Checking Function

● ●

●

ⅹ ●

Integrated test operation function (Cooling)

● ●

ⅹ

● ⅹ

Integrated test operation function (Heating)

● ●

ⅹ

● ●

Inverter backup

●

Dry contact

● ● ⅹ

Snow removal fuction

● ⅹ

Forced defrost

ⅹ ●

Snow Forced defrost

● ●

Static pressure mode

ⅹ ⅹ

ⅹ ● ⅹ

Nigh low noise operation (Cooling only)

● ⅹ ●

Night low noise operation (Cooling/Heating)

● ● ●

Pump down

●

ⅹ

Pump out

●

●

Vacuum mode

● ⅹ ⅹ ●

Selector Fan/ All OFF

ⅹ ⅹ

● ●

ⅹ

ODU Address setting

● ⅹ ⅹ

«
...
45
46
47
48
49
...
»

Содержание Multi V ARUN100LM3


















































































Отзывы:

Нет отзывов