manualshive.com logo in svg

LG MS-72NA, Руководство по обслуживанию

Поделиться
Скачать
LG MS-72NA Скачать руководство пользователя страница 23

5-14

CONDITION

CHECK

RESULT

CAUSE

REMEDY

No microwave
oscillation.

No continuity.

Continuity.

Abnormal

Defective high
voltage
transformer.

Replace high
voltage
transformer.

Normal

Defective timer
motor.

Replace timer
motor.

Check the timer
switch of timer
motor.(cooking
state)

Check high vol-
tage transformer

Abnormal

Defective high
voltage capacitor.

Replace high
voltage capacitor.

Normal

Check high vol-
tage capacitor.

Abnormal

Defective high
voltage diode.

Replace high
voltage diode.

Normal

Check high vol-
tage diode.

Abnormal

Defective
magnetron.

Replace
magnetron.

Check
magnetron.

(TROUBLE 3) No microwave oscillation even though oven lamp and fan motor run.         

NOTE : • Make sure the wire leads are in the correct position.

• When removing the wire leads from the parts, be sure to grasp the connector, not the wires.
• When removing the magnetron, be sure to install the magnetron gasket in the correct position     

and in good condition.

Содержание MS-72NA
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды