LG MS-72NA Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 31

background image

5-8

CAUTIONS

1. DISCONNECT THE POWER SUPPLY CORD FROM THE OUTLET WHENEVER REMOVING THE

OUTER CASE FROM THE UNIT. PROCEED WITH THE TEST ONLY AFTER DISCHARGING THE HIGH
VOLTAGE CAPACITOR AND REMOVING THE WIRE LEADS FROM THE PRIMARY WINDING OF THE
HIGH VOLTAGE TRANSFORMER. (SEE PAGE 2-1)

2. ALL OPERATIONAL CHECKS WITH MICROWAVE ENERGY MUST BE DONE WITH A LOAD (1 LITER

OF WATER IN CONTAINER) IN THE OVEN.

COMPONENTS

TEST PROCEDURE

RESULTS

HIGH VOLTAGE
TRANSFORMER
(Wire leads removed)

MAGNETRON
(Wire leads removed)

1. Measure the resistance.

(Ohm-meter scale: Rx1 and Rx100)
• Primary winding
• Secondary winding
• Filament winding

2. Measure the resistance.

(Ohm-meter scale: Rx1000)
• Primary winding to ground
• Filament winding to ground

1. Measure the resistance.

(Ohm-meter scale: Rx1)
• Filament terminal

2. Measure the resistance.

(Ohm-meter scale: Rx1000)
• Filament to chassis

Approx.: 0.3 ~ 0.8 ohm
Approx.: 100 ~ 200 ohm
Less than: 1 ohm

Normal: Infinite
Normal: Infinite

Normal: Less than 1 ohm

Normal: Infinite

PRIMARY
TERMINAL

SECONDARY
TERMINAL

FILAMENT
WINDING
TERMINAL

COMPONENT TEST PROCEDURE

«
...
15
16
17
18
19
...
»

Содержание MS-72NA
































Отзывы:

Нет отзывов

Похожие инструкции для MS-72NA

Бренд: GE Страницы: 36

Бренд: GE Страницы: 2

Бренд: GE Страницы: 36

Бренд: GE Страницы: 28

Бренд: GE Страницы: 24

Бренд: GE Страницы: 24

Бренд: GE Страницы: 44

Бренд: GE Страницы: 3

Бренд: GE Страницы: 40

Бренд: Maytag Страницы: 13

Бренд: ZANKER Страницы: 48

Бренд: GASLAND chef Страницы: 20

IDF 9011 PRO BK

Бренд: Cata & Can Roca Страницы: 31

Бренд: CDA Страницы: 36

Бренд: Asko Страницы: 48

Бренд: KING Страницы: 16

Бренд: Gorenje Страницы: 100

Бренд: MBM Страницы: 81

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды