manualshive.com logo in svg

LG MS-72NA, Руководство по обслуживанию

Поделиться
Скачать
LG MS-72NA Скачать руководство пользователя страница 19

5-10

COMPONENTS

TEST PROCEDURE

RESULTS

RELAY 2

FAN MOTOR
(Wire leads removed)

TURNTABLE
MOTOR
(Wire leads removed)

Check for continuity of relay 2 with an
ohm-meter.
(Remove wire leads from relay 2 and
operate the unit.)

Measure the resistance.
(Ohm-meter scale: R x 100)

Measure the resistance.
(Ohm-meter scale: R x 1000)

POWER
LEVEL

1

4 sec

18 sec

2

6 sec

16 sec

3

8 sec

14 sec

4

10 sec

12 sec

5

12 sec

10 sec

6

14 sec

8 sec

7

16 sec

6 sec

8

18 sec

4 sec

9

20 sec

2 sec

10

22 sec

0 sec

Normal: 
A~B : Approx. 65 ~ 80 ohm
B~C : Approx. 10 ~ 30 ohm
A~C : Approx. 85 ~ 105 ohm

Abnormal: Infinite or several

ohm.

Normal: Approx. 100 ~ 150 ohm
Abnormal: Infinite or several

ohm.

NOTE : • A MICROWAVE LEAKAGE TEST MUST ALWAYS BE PERFORMED WHEN THE UNIT IS

SERVICED FOR ANY REASON.

• MAKE SURE THE WIRE LEADS ARE IN THE CORRECT POSITION.
• WHEN REMOVING THE WIRE LEADS FROM THE PARTS, BE SURE TO GRASP THE

CONNECTOR, NOT THE WIRES.

Relay 1

Relay 2

A(RD)

B(BK)

C(WH)

Содержание MS-72NA
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды