5-2
PRECAUTIONS ON INSTALLATION
(Figure 2)
A. Plug the power supply cord into a 250 V AC, 50 Hz,
single-phase power source with a capacity of at
least 10 amperes.
B. Since the unit weights about 17kg, be sure to place
it on a sturdy and flat surface.
C. Avoid placing the unit in a location where there is
direct heat or splashing water.
D. Place the unit as far away as possible from TV,
radio, etc. to prevent interference. And do not place
on or near a hot gas or electric burner or in a heated
oven.
CAUTION
GENERAL PRECAUTIONS IN USE
Microwave Oven
A. Never operate the unit when it is empty. Operating
the oven with no load may shorten the life of the
magnetron. Whenever cooking dry foods (dried fish,
bread, etc.) or a small amount of food, be sure to
put a glass of water into the cooking compartment.
The turntable tray may become hot after operating,
be careful when touching it.
B. Aluminum foil should be avoided because it will
disrupt cooking and may cause arcing. However,
small pieces may be used to cover some parts of
food to slow the cooking. Any aluminum foil used
should never be closer than 2.5 cm to any side wall
of the oven.
Toaster
A. Never operate the toaster when it is empty.
Operating the toaster with no load may overheat this
appliance.
B. Oversized food, metal foil packages or utensils must
not be inserted in this toaster, as they may create a
fire or electrical hazards.
TRIAL OPERATION
After installation, the following sequences and results
should be checked carefully.
Microwave Oven
A. Put a container filled with water (about 1 liter) into
the oven, and close the door tightly.
B. Touch the STOP/CLEAR and the COOK TIME keys.
C. Set cooking time for 10 minutes by touching “1”
and then “0” three times. “1000” appears in the
display window.
D. Touch the START key.
Make sure the cavity light comes on. The unit will
begin cooking and the display window will show the
time counting down by seconds.
E. After about 5 minutes, make sure the primary
interlock switch, the secondary interlock switch and
the interlock monitor and oven lamp switch operate
properly by opening and closing the door several
times. Touch the START key each time the door is
closed.
F. Continue operating the unit. Four long beep sound
signal is heard when the time is up. The unit will
shut off automatically.
G. Confirm the water is hot.
Toaster
A. Make sure the crumb tray is pushed all the way in
place plugging in.
B. Remove all protective wrappings from food before
placing into toasting slots. Then place bread into
slots and close the door.
C. Select one mode(Toast).
D. Press the Darkness Control to the desired setting.
E. Press the Start button. Make sure indicator light
comes on. The unit will begin cooking and the
display will show the browning level you selected.
F. After 1 minute, make sure the toaster door switch
and indicator light operate properly by opening and
closing the door several times (In normal state,
indicator light blinks when door is opened).
G. Continue operating the unit by pressing the Start
button. Beep sound signal is heard when the time is
up. The unit will shut off automatically and fan will
blow for 1 minute to cool this toaster.
H. Confirm the bread is cooked.
NOTE : If you operate this toaster for the first time, you
will notice an odor, that is a characteristic of
burning off residues on the new heating
elements. This is normal.
This unit is equipped with a 3-prong plug for your
safety. If the wall outlet is a grounded 3-hole type,
the unit will be grounded automatically.
Three-Pronged(Grounding)
Plug
Figure 2
Properly Polarized and
Grounded
Outlet
Содержание MD-2642KT
