manualshive.com logo in svg

LG MB-308DDD, Руководство по обслуживанию

Поделиться
Скачать
LG MB-308DDD Скачать руководство пользователя страница 18

5-17

CONDITION

CHECK

RESULT

CAUSE

REMEDY

Output is full when
you set lower
power level.

Abnormal.

Defective PCB
assembly.

Replace PCB
assembly.

Disconnect the
wire leads from
relay 2 and check
continuity relay 2. 
(Operate the unit)

(TROUBLE 6) Oven does not cook properly when programmed for the set power level

(Operates properly on HIGH)

CONDITION

CHECK

RESULT

CAUSE

REMEDY

1. Heater is not

operating.

Abnormal.

Malfunction the 
heater.

Replace.

Heater.

Normal.

No continuity.

Open or loosen.

Replace or
connect tightly.

Wire connection.

(TROUBLE 7) Grill

NOTE 

• MAKE SURE THE WIRE LEADS CORRECT POSITION.

• WHEN REMOVING THE WIRE LEADS FROM THE PARTS, BE SURE TO GRASP THE CONNECTOR

NOT THE WIRES.

• WHEN REMOVING THE MAGNETRON, BE SURE TO INSTALL THE MAGNETRON GASKET IN THE

CORRECT POSITION AND IN GOOD CONDITION.

2. Lower tempera-
ture in the oven.

Abnormal.

Malfunction the 
heater.

Replace.

Heater.

Normal.

Abnormal.

Defective PCB
assembly.

Replace PCB
assembly.

Disconnect the
wire leads from
relay 3 and check
continuity relay 3. 
(Operate the unit)

Содержание MB-308DDD



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды