manualshive.com logo in svg

LG MB-308DDD, Руководство по обслуживанию

Поделиться
Скачать
LG MB-308DDD Скачать руководство пользователя страница 16

5-15

CONDITION

CHECK

RESULT

CAUSE

REMEDY

1. Setting time

does not count-
down when
touching START
pad.

2. Fan motor or

oven lamp do
not turn on.

No continuity.

Continuity.

Certainly

Defective PCB
assembly.

Loose  connection.

Replace PCB
assembly.

Connect them
tightly.

No certainly.

Abnormal

Check fan motor.

Defective fan motor.

Replace fan motor.

Abnormal

Check oven lamp.

Defective oven lamp.

Replace oven lamp.

Defective sec-
ondary switch.

Replace sec-
ondary switch.

Check continuity
of secondary
switch (with
door closed).

Check the con-
nection between
3 pin connector
and PCB
assembly.

Normal

Defective PCB
assembly.

Replace PCB
assembly.

(TROUBLE 3) Display shows all figures set, but oven does not start cooking while desired         

program times are set and START pad is touched.

(TROUBLE 4) Oven seems to be operating but little heat is produced in oven load.

NOTE : Simple test of power output-conducted by heating one liter water for one min. if available.

Minimum 8.5°C temperature rise is normal condition.

CONDITION

CHECK

RESULT

CAUSE

REMEDY

Output is low

Lower than 90% of
rating voltage.

Normal

Abnormal

Defective PCB
assembly.

Replace PCB
assembly.

Normal

Abnormal

Measure the out-
put power.

Defective  mag-
netron.

Replace  mag-
netron.

Decrease in power
source voltage
with load.

Suggest customer
contact local elec-
tric power utility
co. or qualified
electrician.

Check the
power source
voltage.

Disconnect the
wire leads from
relay 2 and
check on and off
time with multi-
tester.

Содержание MB-308DDD



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды