LG LV420HV Скачать руководство пользователя

Страница: 67 / 70

Cautions for Refrigerant Leaks

CAUTIONS FOR REFRIGERANT LEAKS

Due to our policy of continuous product innovation, some specifications may change without notification.

Amount of

Factory-Charged

Refrigerant per

Outdoor Unit

Amount of

Additional

Refrigerant

Trim Charge

Refrigerant Concentration Limit (RCL) Calculations

To calculate total refrigerant amount per system:

Cautions for Refrigerant Leaks / Introduction

ASHRAE Standards 15-2010 and 34-2010 offer guidelines that address refrigerant safety and the maximum allowable concentration of refrig-

erant in an occupied space. Refrigerant will dissipate into the atmosphere, but a certain volume of air is required for this to occur safely. For

R410A refrigerant, the maximum allowable concentration is 0.026 lbs./ft3 per 1,000 ft3 of air in an occupied space. Buildings with twenty-four

(24) hour occupancy allow half of that concentration.

ASHRAE Standards 15 and 34 assume that if a system develops a leak, its entire refrigerant charge will dump into the area where the leak

occurs. To meet ASHRAE Standards 15 and 34, calculate the refrigerant concentration that may occur in the smallest room volume on

the system, and compare the results to the maximum allowable concentration number (see below for information on how to calculate the

refrigerant concentration).

Also consult state and local codes in regards to refrigerant safety.

American Society of Heating, Refrigeration and Air Conditioning Engineers, Inc. (ASHRAE). Atlanta, GA. ASHRAE, Inc. Information about

ASHRAE Standard 15-2010 / 34-2010 and addenda current as of the date of this publication.

Take appropriate actions at the end of HVAC equipment life to recover, recycle, reclaim or destroy R410A refrigerant according to applicable US

EPA rules.

Total System

Refrigerant

Charge

To calculate the potential refrigerant concentration level (RCL):
1. Measure the occupied space dimensions (in feet).

2. Calculate the cubic foot volume of air in the smallest occupied

space. (To obtain a detailed overview of the RCL, perform the

same calculations to the second smallest zone, the third smallest

zone until the RCL is obtained for all zones. Also, pay special

attention to areas such as basements, etc., where refrigerant

cannot dissipate easily.)

3. Divide the refrigerant charge of the Single Zone system serving

the area in pounds by the results of step 1.

4. If the calculation indicates that the potential refrigerant concen-

tration level is higher than the allowed RCL, increase the cubic

volume of the smallest occupied space or modify the piping

system design.

5. The allowable RCL limit for most applications must be equal to

or less than 0.026 lbs./ft

. However, in special occupied spaces,

such as hospitals and nursing homes, where occupants may have

limited mobility, the allowable RCL limit is cut in half. See ASHRAE

Standard 34-2007 and local codes for detailed information.

RCL (lbs./ft

) =

Total System Refrigerant Charge (lbs.)

Volume of Smallest Occupied Space (ft

)

Refrigerant Leaks

Verify the maximum refrigerant concentration level in the space where the indoor unit will be mounted meets the concentration limit for the

application. If the refrigerant leaks and safety limits are exceeded, it could result in personal injuries or death from oxygen depletion.

Содержание LV420HV







































































Результаты поиска

Содержание LV420HV

Отзывы:

Похожие инструкции для LV420HV

Бренды по названию

Популярные бренды

LG LV420HV, Руководство по установке

Результаты поиска

Содержание LV420HV

Отзывы:

Похожие инструкции для LV420HV

Бренды по названию

Популярные бренды