LG LV420HV Скачать руководство пользователя

Страница: 48 / 70

Single Zone V

ertical

Air Handling Unit Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.

ELECTRICAL SYSTEM INSTALLATION

Communication / Connection (Power) Cable Specifications from Outdoor

Unit to Indoor Unit

Figure 65: Single Zone Outdoor Unit to Indoor Unit Wiring and Commu-

nications Cable Diagrams.

7/16

" ± 1/8

13/16

GN/YL

Power Wiring, Ground

to Outdoor Unit

Communication / Connection

(Power), Ground Cable

From Outdoor Unit

To Indoor Unit

13/16

GN/YL

GN/YL = (Ground, Yellow)

7/16

" ± 1/8

• For communication / connection (power) wires between the Single

Zone outdoor unit and the indoor unit, use a minimum 18 gauge,

four (4) conductor, stranded, shielded or unshielded wire. If shield-

ed, the wire must be grounded to the chassis at the outdoor unit

only.

• Install insulation material as required by local code.
• Firmly attach the cable; provide slack but secure in a way to pre-

vent external forces from being imparted on the terminal block.

• Wiring must be completed without splices.

• Always verify the communication cable is connected to a commu-

nications terminal on the Single Zone unit.

Never apply line

voltage power to the communication cable connection. If contact is

made, the PCBs may be damaged.

• The shield of the communications cable connecting the outdoor unit to

the indoor unit must be grounded only to the outdoor unit frame.

• Tie the shield of each cable segment together using a wire nut at the

indoor unit. Maintain polarity throughout the communication network.

• Position the incoming power to the outdoor unit away from the power

/ communications cables from the outdoor unit to the indoor unit.

•

Never use a common multiple-core communications cable.

Figure 66: General VAHU Power / Communication System Diagram.

Содержание LV420HV







































































Результаты поиска

Содержание LV420HV

Отзывы:

Похожие инструкции для LV420HV

Бренды по названию

Популярные бренды

LG LV420HV, Руководство по установке

Результаты поиска

Содержание LV420HV

Отзывы:

Похожие инструкции для LV420HV

Бренды по названию

Популярные бренды