LG LV420HV Скачать руководство пользователя страница 39

Страница: 39 / 70

Refrigerant Piping Connections

Due to our policy of continuous product innovation, some specifications may change without notification.

REFRIGERANT PIPING CONNECTIONS

Outdoor Unit Connections

Outdoor Unit Connections

1. Remove the ODU front panel by loosening the fastening screws.

2. Align the center of the refrigerant piping and corresponding

connection as shown.

3. Refer to the figures at right for liquid and gas piping attachments

onto the outdoor unit.

4. Place a couple of drops of PVE refrigerant oil on outside of the

flare before assembling.

Do not add any contaminants.

Tighten the flare nut initially by hand.

5. Finish tightening the flare nut with a torque wrench until the

wrench clicks. Follow torque guidelines in the table below. See

figures for correct connection points.

Figure 44: LUU188HV, LUU248HV Outdoor Unit Piping Connection

When tightening the flare nut with a torque wrench, ensure the direction

for tightening follows the arrow on the wrench.

Table 15: Torque Wrench Tightening.

Pipe Size (in. OD)

Outside Diameter (mm)

Torque (lbs-ft)

1/4

6.35

13.0 - 18.0

3/8

9.52

24.6 - 30.4

1/2

12.7

39.8 - 47.7

5/8

15.88

45.4 - 59.3

3/4

19.05

71.5 - 87.5

Figure 43: LUU368HV, LUU428HV, LUU488HV Outdoor Unit Piping

Connection

Figure 45: Pipe Attachment.

Piping can be installed

in one of four different

layouts.

Liquid

Vapor

Liquid Vapor

Front, Side, and

Rear Connections

Available

Содержание LV420HV







































































Результаты поиска

Содержание LV420HV

Отзывы:

Бренды по названию

Популярные бренды

LG LV420HV, Руководство по установке

Результаты поиска

Содержание LV420HV

Отзывы:

Бренды по названию

Популярные бренды