LG LV420HV Скачать руководство пользователя

Страница: 32 / 70

32 | INTRODUCTION

Single Zone V

ertical

Air Handling Unit Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.

No Pipe Size Substitutions

Use only the pipe size selected by the information in this manual. Using a different size is prohibited and may result in a system malfunction

or failure to work at all.

No In-line Refrigeration Components

Components such as oil traps, solenoid valves, filter-driers, sight glasses, tee fittings, and other after-market accessories are not permitted

on the refrigerant piping system between the outdoor unit and the indoor unit. Sight-glasses and solenoid valves may cause vapor to form in

the liquid stream. Over time, driers may deteriorate and introduce debris into the system. The designer and installer must verify the refriger-

ant piping system is free of traps, sagging pipes, sight glasses, filter driers, etc.

Field-Provided Isolation Ball Valves

LG maintains a neutral position on using isolation valves in refrigerant piping systems. LG does not endorse any manufacturer of isolation

valves. It is recognized that installing isolation valves may simplify future maintenance requirements, and, if used, considerations must be

taken including, but not limited to, the following:

• Pressure drops for any component used, including isolation valves, must be known in equivalent pipe length and calculated into the total

and segment equivalent piping lengths and compared to product design limitations.

• In all cases, materials must be suitable for the application and any applicable codes, including, but not limited to, diameter and wall thick-

ness continuity per ACR standards.

Failure to do so may cause significant performance degradation. Proper leak checks must be performed. Using isolation valves does not

automatically void any LG product warranty, however, a limited warranty may be voided in whole or part must any field supplied accessory

fail in any way that causes product failure.

REFRIGERANT SYSTEM ENGINEERING

Proper system operation depends on the installer using utmost care while assembling the piping system. The following pages are an over-

view of best practices when installing the refrigerant piping system.

LG Electronics U.S.A.,Inc., is not responsible for any piping calculations, refrigerant leaks, degradation of performance, any other potential problems

or damages caused by the interconnecting piping, their joint connections, isolation valves, or introduced debris inside the piping system.

Component

Size (Inches)

Elbow (ft.)

1/4

3/8

1/2

5/8

3/4

0.5

0.6

0.7

0.8

1.2

Table 12: Equivalent Piping Length for Elbows.

Using Elbows

Field-supplied elbows are allowed if they are long radius and designed for

use with R410A refrigerant. The designer and installer, however, must be

cautious with the quantity and size of fittings used, and must account for

the additional pressure losses in equivalent pipe length calculation for each

branch. The equivalent pipe length of each elbow must be added to each

pipe segment manually (Table 12).

Pipe Bends

When bending soft copper, use long radius bends. Refer to the “Radii of Coiled Expansion Loops and Developed Lengths of Expansion

Offsets” table for minimum radius specifications.

Содержание LV420HV







































































Результаты поиска

Содержание LV420HV

Отзывы:

Похожие инструкции для LV420HV

Бренды по названию

Популярные бренды

LG LV420HV, Руководство по установке

Результаты поиска

Содержание LV420HV

Отзывы:

Похожие инструкции для LV420HV

Бренды по названию

Популярные бренды