LG LRSC26920TT Скачать руководство пользователя страница 58

Страница: 58 / 106

- 64 -

TROUBLE DIAGNOSIS

CLAIMS.

CAUSES AND CHECK POINTS.

HOW TO CHECK

3. Refrigeration

is weak.

3) Cooling air leak.

4) No cooling air circulation.

Residual
frost.

No automatic defrosting.

Defrost does not return.

Bad gasket adhestion

Door sag.

Faulty fan motor.

Weak heat from heater.

Too short defrosting time.

Defrost Sensor.

- Faulty characteristics.

Seat-D (missing, location. thickness).

Structural fault.

Gasket gap.

Air inflow through the fan motor.

Bad insulation of case door.

Sheath Heater - rated.

Heater plate

Heater cord-L

Gap.
Bad attachment.
Contraction.

Bad adhesion.
Weak binding force at hinge.

Fan motor.

Door switch.

Self locked.
Wire is cut.
Bad terminal contact.

Contact distance.
Button pressure.
Melted contact.
Contact.

Poor door
attachment.
Door liner
(dimension).
Contraction inner
liner.
Misalignment.
Bad terminal
connection.
Adiabatics liquid
leak.

Faults.

Refrigerator and freezer switch reversed.
Button is not pressed.

No contact to drain.
Loosened stopper cord.

Not touching the
evaporator pipe.
Location of assembly
(top and middle).

■

Check the fan motor
conduction: OK.
No conduction: NG.

Содержание LRSC26920TT











































































































Результаты поиска

Содержание LRSC26920TT

Отзывы:

Похожие инструкции для LRSC26920TT

Бренды по названию

Популярные бренды

LG LRSC26920TT, Руководство по обслуживанию

Результаты поиска

Содержание LRSC26920TT

Отзывы:

Похожие инструкции для LRSC26920TT

Бренды по названию

Популярные бренды