LG LRSC26920TT Скачать руководство пользователя страница 22

Страница: 22 / 106

2-17. Test Function

1. The test function is a self-diagnostic system designed to detect problems early and to make diagnosis and repair easier

and quicker.

2. The test button is on the main PCB. Test mode can run for up to 2 hours and will then default to the normal operation

mode if not reset manually.

3. The function buttons are inoperable when the refrigerator is in test mode.

4. When you have finished using the test mode, reset the appliance manually by unplugging it for several seconds.

5. If nonconforming contents such as sensor failure are found during performance of test mode, release the test mode and

display the failure code.

6. The test button is inoperable if the display is showing failure codes. Reset the appliance manually to use the test button.

MICOM FUNCTION

- 28 -

Test 1

Test 2

Normal

Status

Mode

Operation

Contents

Remarks

Press test button once
(strong cold mode)

Press test button once at
the test mode 1 status
(forced defrost mode)

Press test button once at
the test mode 2 status

1. Continuous operation of compressor
2. Continuous operation of freezing BLDC motor

(high-speed RPM) and cooling BLDC motor

3. Defrost heater turns off
4. Stepping motor damper is completely opened

(baffle open)

5. Optichill stepping motor damper is completely

closed.

6. All display LEDs or LCD graphics turn on.

1. Compressor OFF
2. Freezing BLDC motor and cooling BLDC

motor turn off

3. Defrost heater turns on
4. Stepping motor damper is completely closed

(baffle close)

5. Optichill stepping motor damper is completely

closed.

6. All display LEDs or LCD graphics turn off.

Except for (A), (B) LCD graphic.
Except for (A): 22 (B): 22 LEDs.

Return to the initial status.

Freezer fan is off when
door is open.

Return to the normal mode
when the defrost sensor is
above +5°C

Compressor will operate
after delay for 7 minutes

EXPRESS

DIGITAL CONTROL

FRZ TEMP

REF TEMP

JET

CUBE

FILTER RESET

HOLD 3SECS

ROOM TEMP

LOCK

DISPENSER & KEY

WATER

CRUSH

3 SECS

FILTER

5
4
3
2
1

ICEBEAM
COOLING

CUBE

FILTER

MONTH

ROOM TEMP

DISPENSER & KEY

WATER

5
4
3
2
1

CRUSH

3 SECS

EXPRESS FRZ

LOCK

JET

3 SECS

FILTER LIGHT

TEST MODE1 STATUS DISPLAY

TEST MODE2 STATUS DISPLAY

Содержание LRSC26920TT











































































































Результаты поиска

Содержание LRSC26920TT

Отзывы:

Похожие инструкции для LRSC26920TT

Бренды по названию

Популярные бренды

LG LRSC26920TT, Руководство по обслуживанию

Результаты поиска

Содержание LRSC26920TT

Отзывы:

Похожие инструкции для LRSC26920TT

Бренды по названию

Популярные бренды