LG LRSC26920TT Скачать руководство пользователя страница 86

Страница: 86 / 106

TROUBLE DIAGNOSIS

- 92 -

Items

Precautions

4. Vacuum degassing.

Pipe Connection

Connect the red hose to the high pressure side and the blue hose to the

low pressure side.

Vacuum Sequence

Open valves

and

and evacuate for 40 minutes. Close valve

5. Refrigerant charging.

Charging sequence

1) Check the amount of refrigerant supplied to each model after completing vacuum

degassing.

2) Evacuate charging canister with a vacuum pump.

3) Measure the amount of refrigerant charged.

- Measure the weight of an evacuated charging canister with an electronic scale.

- Charge refrigerant into a charging canister and measure the weight. Calculate the weight

of refrigerant charged into the charging canister by subtracting the weight of an

evacuated charging canister.

KEY POINT

- If power is applied

during vacuum
degassing, vacuum
degassing shall be
more effective.

- Run the compressor

while charging the
system. It is easier
and works better.

KEY POINT

- Be sure to charge the

refrigerant at around
25°C [77°F].

- Be sure to keep -5g in

the winer and +5g in
summer.

the amount of refrigerant charged= weight after charging -
weight before charging (weight of an evacuated cylinder)

Calculation of amount of refrigerant charged

Compressor

Low

pressure

Condenser

High

pressure

Drier

Evaporator

Red

Yellow

Blue

Vaccum

Pump

Suction pipe

Hot Line

R134a

Indicate the weight of an
evacuated charging canister

Содержание LRSC26920TT











































































































Результаты поиска

Содержание LRSC26920TT

Отзывы:

Похожие инструкции для LRSC26920TT

Бренды по названию

Популярные бренды

LG LRSC26920TT, Руководство по обслуживанию

Результаты поиска

Содержание LRSC26920TT

Отзывы:

Похожие инструкции для LRSC26920TT

Бренды по названию

Популярные бренды