LG LRSC26920TT Скачать руководство пользователя страница 72

Страница: 72 / 106

TROUBLE

IAGNOSIS

-7
8-

Problems

Causes

Checks

Measures

Remarks

Ice in the freezer 1) Bad cooling air circulation.

- Check food storage conditions

- Be acquainted with how to use.

- Check the parts related

compartment.

- Intake port is clogged in the freezer

visually.(Check clogging at intake

- Check defrost (Check ice on the

to defrosting if the

- Surface of fan

compartment.

and discharging port of cooling air.)

evaporator and pipes after forced

problem is caused by

grille.

- Discharging port is Clogged.

- Check food occupation ratio in

defrosting).

the faulty defrosting.

- Wall of freezer - Too much food is stored.

volume (Less than 75%).

compartment.

- Bad defrosting.

- Check frost on the evaporator after

- Cool air

dissembling shroud and fan grille.

discharging port.

- Check icing at intake port of

- Basket(rack)

refrigerator compartment.

area.

- Food surface.

2) Bad freezer compartment door

- Check gasket attachment

- Correct the gasket attachement

- Replace when it can not

- Icing in the

- Faulty gasket

conditions.

conditions and replace it.

be repaired.

shute.

- Faulty assembly

- Check door assembly conditions.

- Door assembly and replacement.

3) Over freezing in the freezer

- Refrigerator operates pull down.

-Replace defective parts.

compartment.

(Check if it is operated

- Faulty MICOM.

intermittently)

- The Temperature of freezer

compartment is satisfactory, but

over freezing happens in the

refrigerator compartment even

though the notch is set at weak.

4) Bad defrosting.

- Check frost on the evaporator after

- Check parts related to defrosting.

- Heater wire is cut.

dissembling shroud and grille.

- Check defrosting. Check ice on the

- Faulty defrost sensor.

- Check ice on the intake port in the

evaporator and pipes after forced

- Defrosting cycle

refrigerator compartment.

defrosting.

5) User is not familiar with how to

- Check food holds door open.

- Be acquainted with how to use.

use.

- Check ice on the ice tray.

- Door opens.

- High moisture food water is stored.

Содержание LRSC26920TT











































































































Результаты поиска

Содержание LRSC26920TT

Отзывы:

Похожие инструкции для LRSC26920TT

Бренды по названию

Популярные бренды

LG LRSC26920TT, Руководство по обслуживанию

Результаты поиска

Содержание LRSC26920TT

Отзывы:

Похожие инструкции для LRSC26920TT

Бренды по названию

Популярные бренды