background image

4

SAFETY INSTRUCTIONS

 

When the power cord is to be replaced, replacement work shall be performed by authorized 

personnel only using only genuine replacement parts.

 

and authorized personnel only.

 

Connect to a properly rated, protected, and sized power circuit to avoid electrical overload.

 

Always plug into a grounded outlet.

 

Do not under any circumstances, cut or remove the third (ground) prong from the power cord.

 

When installing or moving the appliance, be careful not to pinch, crush, or damage the power 

cord.

 

Plug in the power plug properly.

 

Do not modify or extend the power cord.

 

Do not start/stop operation by plugging/unplugging the power cord.

 

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or 

similarly qualified person in order to avoid a hazard.

 

Use a dedicated circuit.

 

Do not disassemble or modify the product.

 

Adhere to all industry recommended safety procedures including the use of long-sleeved gloves 

and safety glasses.

 

Use care when unpacking and installing. The edges of the product may be sharp.

 

Disconnect the power cord or circuit breaker before installing or servicing the appliance.

 

Keep packaging materials out of the reach of children. These materials can pose a suffocation 

risk to children.

 

Store and install the product where it will not be exposed to temperatures below freezing or 

exposed to outdoor weather conditions.

 

other appliance.

OPERATION

 

Use this appliance only for its intended purpose.

 

Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, 

or has missing or broken parts, including a damaged cord or plug.

 

Repair or immediately replace all power cords that have become frayed or otherwise damaged. 

Do not use a cord that shows cracks or abrasion damage along its length or at either end.

 

Do not run cord under carpets or mats where it could be stepped on and damaged.

 

Keep the cord out from under heavy objects like tables or chairs.

 

Do not place the power cord near a heat source.

 

Do not use an adaptor or plug the product into a shared outlet.

 

Do not tamper with controls.

 

If you detect a strange sound, a chemical or burning smell, or smoke coming from the appliance, 

unplug it immediately, and contact an LG Electronics Customer Information Center.

 

straight out from the outlet.

 

Do not grasp the power cord or touch the appliance controls with wet hands.

Do not turn on the circuit breaker or power under condition that front grille, cabinet, control box 

are removed or opened. Otherwise, it may cause fire, electric shock, explosion or death.

Содержание JW-Q18WUXA1

























Отзывы: